Skip to content
  • On order
Reinforced inlet valves VW Ford VR6 2.8 12V AAA AMY AFP Reinforced inlet valves VW Ford VR6 2.8 12V AAA AMY AFP

Reinforced inlet valves VAG Ford VR6 2.8 12V AAA AMY AFP

€180.97 (tax incl.)
€226.21 (tax incl.) -20%

Set of 6 reinforced inlet valves for VW VR6 2.8 12-valve (Golf III and IV, Vento, Bora, Corrado, Passat, Sharan) and FORD Galaxy 2.8 VR6.

  • Brands: SUPERTECH, FERREA
  • Engines: AAA, AMY, AFP
  • Dimensions: 39 to 42 mm head, 7 mm stem
  • Material: black nitride stainless steel (SUPERTECH), 1 or 3 grooves
VWIVN-1007-6
0 in stock in France
ORDER TODAY, WE SHIP IN 5 - 15 DAYS
Pay in installments

VW and FORD engines covered

Volkswagen's 12-valve VR6 2.8 is a 2,792 cc six-cylinder with 2 valves per cylinder, from 163 to 177 hp depending on version. It powers the Golf III and Vento, the Corrado, the Passat B3/B4 and the Sharan (AAA and AMY codes), then the Golf IV and Bora (AFP code), from 1991 to 2005. From 1995 to 2000 the first generation Galaxy (WGR) used the 2.8 litre VR6 six-cylinder of Volkswagen origin, with 12 valves, two per cylinder. Coded AAA then AMY, it delivers 174 hp, in front-wheel drive as well as four-wheel drive.

The engine has 6 Volkswagen 021 109 601 L inlet valves, with a 39 mm head and a 7 mm stem, 105.95 mm long. Sharper camshafts, firmer springs, a supercharger or a turbo load them well beyond stock use.

SUPERTECH and FERREA reinforced inlet valves

On the 12-valve VR6, every cylinder relies on just one inlet valve. When the VR6 is revved hard, it leaves its seat and slams back dozens of times each second, and its stem never stops sliding through the guide. Its working range sits at 400 to 550 °C, where the original chromium-silicon steel is already fading: 500 MPa at 500 °C becomes 250 MPa at 600 °C, just beyond, which is 50 % less. Add lift, spring rate, revs or boost and the valve takes more impact, friction and heat every time.

On the SUPERTECH side, the stainless steel receives a black nitride finish: a harder, smoother surface, so the stem rubs and wears less against its guide. The stem is slimmed right under the head while the underside of the head is back-cut; both shapes save weight. On the FERREA side, these are Competition Plus valves, with a stainless body, a chromed stem and a flat head that lifts compression. The maker quotes 20 % gains in hot strength as well as fatigue life, and seat longevity up by 25 %.

In oversize form, only the head changes: 40 mm (+1 mm, FERREA), 41 mm (+2 mm, both brands) or 42 mm (+3 mm, SUPERTECH) versus 39 mm standard; the stem stays at 7 mm. Through a wider seat opening flows more mixture, each cylinder charges better and the VR6 makes more power, provided all 6 inlet seats get machined to the selected size.

Inlet valve technical specification

Part numberBrandSizeHead Ø
OEM 39 mm
Stem Ø
OEM 7 mm
Length
OEM 105.95 mm
GroovesMaterial
VWIVN-1007-6 SUPERTECH Standard 39.0 mm 7 mm 105.95 mm 3 Black nitride stainless steel
VWIVN-1010-6 SUPERTECH +2 mm 41.0 mm 7 mm 105.95 mm 3 Black nitride stainless steel
VWIVN-1011-6 SUPERTECH +3 mm 42.0 mm 7 mm 105.95 mm 3 Black nitride stainless steel
F1931P*6 FERREA Standard 39.0 mm 7 mm 106.15 mm 1 Stainless, chrome stem
F1919P*6 FERREA +1 mm 40.0 mm 7 mm 106.15 mm 1 Stainless, chrome stem
F2136P*6 FERREA +2 mm 41.0 mm 7 mm 106.15 mm 1 Stainless, chrome stem

VWIVN-1007-6, VWIVN-1010-6 and VWIVN-1011-6: undercut stem under the head and back cut.

F1931P*6, F1919P*6 and F2136P*6: flat face for higher compression; FERREA K10099 collets required, with FERREA E11039 retainers or the original retainers.

Fitting details

PartOriginalReinforced
Collets KPR-VW7-T-24 (3 grooves) / K10099 (FERREA, 1 groove)
Valve stem seals VS-VW7I-6
Valve guide

FERREA requires its K10099 collets with its single-groove valves, whether the original retainers are kept or FERREA E11039 retainers are fitted.

The oversizes need inlet seats cut to the new head diameter: 40 mm (+1 mm), 41 mm (+2 mm) or 42 mm (+3 mm).

The 12-valve VR6 uses hydraulic tappets: there is no valve clearance to set after the replacement.

Technical guide

Our brands

SUPERTECH SUPERTECH works out of San Jose, California, and has designed racing valvetrain parts for more than 30 years. Each valve starts from the drawing of one given engine, goes through ultrasonic, X-ray and laser checks, then gets refined with partner engine builders, from drag strip to track.
FERREA Two engine builders from Argentina set up FERREA Racing Components in Florida in 1978, at Fort Lauderdale, and everything is still made in-house. Forged as one piece out of bar, every valve is fully finished on CNC machinery and raced in NASCAR, drag racing and on circuits.

How to choose

Seated in the groove beneath the retainer, the collets hold the valve. Groove shape and count set how the stem is gripped, so what loads the valve will take.

CriterionOption 1Option 2
Size Standard size
39 mm head and 7 mm stem: a direct fit, no rework, on a VR6 head whose inlet seats are still at factory diameter.
+1 to +3 mm
40, 41 or 42 mm head depending on brand: the seat flows more air and the engine gains power, in the region of 10 to 12 cfm per millimetre of head. Seats have to be recut to suit, enlarged ports being ideal; this size also rescues seats that were reground before.
Grooves 3 grooves
Factory design, stem free to spin. For a road VR6 whose springs and revs remain near standard; refit with new collets (KPR-VW7-T-24). Limit: at high revs, the lower groove, where the stem is slimmest, takes most of the load.
Single groove
Here the collet clamps onto the stem: the groove barely carries anything and the broader bearing area cuts wear. The valve then handles stronger springs, big lift and high revs, for track, drift or rally use. FERREA K10099 collets are mandatory, paired with FERREA E11039 retainers or the standard ones.

When reinforced valves become necessary

  • Sharper camshafts or stronger valve springs
  • Higher rev limit
  • Turbo or supercharger conversion on the VR6
  • Head reconditioned for track, drift or rally
  • Original Volkswagen valves worn, marked or recut to repair size

Compatible vehicles

ModelEngine codePowerYears
FORD Galaxy I (WGR) 2.8 i V6 AAA, AMY 174 hp 1995-2000
FORD Galaxy I (WGR) 2.8 i V6 4x4 AAA, AMY 174 hp 1996-2000
VW Corrado (53I) 2.8 VR6 AAA 174 hp 1991-1995
VW Golf III (1H1) 2.8 VR6 AAA 163-174 hp 1992-1997
VW Vento (1H2) 2.8 VR6 AAA 163-174 hp 1992-1998
VW Passat B3/B4 (3A2, 35I) 2.8 VR6 AAA 174 hp 1991-1996
VW Passat B3/B4 Variant (3A5, 35I) 2.8 VR6 AAA 174 hp 1991-1997
VW Sharan (7M8, 7M9, 7M6) 2.8 VR6, VR6 Syncro AAA / AMY 174 hp 1995-2000
VW Golf IV (1J1) 2.8 VR6 AFP 177 hp 1999-2002
VW Golf IV Variant (1J5) 2.8 V6 AFP 177 hp 2000-2004
VW Bora I (1J2) 2.8 VR6 AFP 177 hp 1998-2005
VW Jetta III (1K2) 2.8 VR6 AAA 174 hp 2009-2010

OEM part number (inlet valve): 021 109 601 L

Important: these sets cover the 12-valve VR6 2.8 engines of VW cars; the Ford Galaxy 2.8 V6 has its own page, and the 24-valve VR6 engines (2.8 BDF, 3.2 R32) take other valves.

Related products

VR6 head due for a rebuild: fit new inlet and exhaust valves, plus new stem seals. The parts designed for this engine are listed below:

VW VR6 2.8 AAA exhaust valves →
VW VR6 2.8 AAA inlet valve stem seals →

16 other products in the same category

Viewed products

Loading...