- On order
Reinforced exhaust valves VAG Ford VR6 2.8 12V AAA AMY AFP
Set of 6 reinforced exhaust valves for the VW VR6 2.8 12-valve (Golf III and IV, Vento, Bora, Corrado, Passat, Sharan) and the Ford Galaxy 2.8 VR6.
- Brands: SUPERTECH, FERREA
- Engines: AAA, AMY, AFP
- Dimensions: 34 to 36 mm head, 7 mm stem
- Material: stainless steel, Inconel or Super Alloy, 1 or 3 grooves
VW and Ford engines covered
The 2.8 litre 12-valve VR6 is a compact six-cylinder with a single cylinder head, developed by Volkswagen. Under the codes AAA and AMY it delivers 163 to 174 hp in the Golf III, Vento, Corrado, Passat B3 and B4 and Sharan, as well as in the first generation Ford Galaxy; under the code AFP it gives 177 hp to the Golf IV and Bora, from 1991 to 2005.
Each cylinder has a single exhaust valve: the engine has 6 of them, with a 7 mm stem. The versions offered here start from the standard size, with a 34.0 to 34.2 mm head, and go up to 36 mm. When the load, the revs or the boost pressure rise, these original valves take more heat and more shocks than they were designed for.
SUPERTECH and FERREA reinforced exhaust valves
A quirk of the VR6 2.8 12V: one exhaust valve per cylinder, left alone to push out the whole burnt charge. On the metal side, its head lives between 760 and 870 °C without boost and clears the 1,000 °C mark with a turbo or supercharger. It sheds that heat almost only by contact, roughly 75 % through the seat and 20 % through the guide. Take an EV8 steel as the yardstick: 550 MPa at 600 °C, yet no more than 300 MPa at 800 °C. As soon as tuning raises load or revs, the head crosses that line, wears, warps and the seal it should provide simply disappears.
To cope, the reinforced valve adopts another material. On the SUPERTECH side, two options: stainless with black nitriding, protected by a hard surface layer that slows wear, and Inconel, a nickel alloy built for high heat and credited with 860 MPa at 732 °C and 554 MPa at 816 °C, close to 85 % above EV8 around 800 °C. On the FERREA side, the Competition Plus in stainless with a chromed stem claims a 20 % gain in hot strength and a seat that lives 25 % longer; the Super Alloy, nickel based, targets boosted engines.
The oversized versions (+1, +1.8 and +2 mm) only enlarge the head, from 34 to 35 or 36 mm. The area offered to the gases grows, scavenging speeds up, power rises; in return, all 6 exhaust seats have to be cut to suit the chosen diameter, ideally as part of a full cylinder head overhaul.
Exhaust valve technical specifications
| Part number | Brand | Size | Head Ø | Stem Ø | Length | Grooves | Material |
|---|---|---|---|---|---|---|---|
| VWEVN-1007-6 | SUPERTECH | Standard | 34.2 mm | 6.95 mm | 106.95 mm | 3 | Black nitrided stainless |
| F1932P*6 | FERREA | Standard | 34.0 mm | 6.96 mm | 106.9 mm | 1 | Stainless steel, chrome stem |
| F1920P*6 | FERREA | +1 mm | 35.0 mm | 6.96 mm | 106.9 mm | 1 | Stainless steel, chrome stem |
| F1921P*6 | FERREA | +1 mm | 35.0 mm | 6.96 mm | 106.9 mm | 1 | Super Alloy (nickel base) |
| VWEVN-1010-6 | SUPERTECH | +1.8 mm | 36.0 mm | 6.95 mm | 106.95 mm | 3 | Black nitrided stainless |
| VWEVI-1010-6 | SUPERTECH | +1.8 mm | 36.0 mm | 6.95 mm | 106.95 mm | 3 | Inconel |
| F2135P*6 | FERREA | +2 mm | 36.0 mm | 6.96 mm | 106.9 mm | 1 | Super Alloy (nickel base) |
Valve fitting
| Part | VW / Ford original | Reinforced |
|---|---|---|
| Collets | KPR-VW7-T (3 grooves) | |
| Valve stem seals | VS-VW7E | |
| Valve guide |
The 3-groove SUPERTECH valves are fitted with 3-groove collets such as the KPR-VW7-T; the FERREA valves have a single groove and need collets designed for that single groove, never the original ones.
A head enlarged by 1, 1.8 or 2 mm requires the 6 exhaust seats to be recut to the diameter of the chosen valve: plan a visit to the machine shop when the cylinder head is rebuilt.
The 7 mm stem slides in the guide: check its clearance and replace the exhaust valve stem seals on reassembly.
Technical guide
Our brands
| SUPERTECH has worked on competition valvetrains from San Jose, California, for over 30 years: valves, springs, guides, plus retainers machined from titanium. Every model is drawn for one precise engine, then proven in racing with tuners on circuits, rally stages and drag strips. | |
| FERREA came to life in 1978 under the drive of Horacio Ferrea, backed by Daniel Urrutia. The brand machines, in Florida as in Argentina, stainless, titanium or nickel superalloy valves, fitted to road builds as much as to racing engines, from NASCAR to endurance and drag racing. |
How to choose
SUPERTECH valves have 3 grooves, FERREA valves a single one: the groove therefore sets the type of collets to fit. Next come head size, which decides seat machining, and material, chosen for how the engine is used.
| Criterion | Option 1 | Option 2 |
|---|---|---|
| Size | Standard, 34.0 or 34.2 mm For a head whose exhaust seats keep their diameter: a light regrind is enough, with no machining to a new size. SUPERTECH VWEVN-1007 in black nitrided stainless, 34.2 mm head; FERREA F1932P in Competition Plus, 34.0 mm head. |
+1, +1.8 or +2 mm, 35 or 36 mm A wider head raises flow, by around 10 to 12 cfm per millimetre gained, and power follows; machining the seats also rescues a head that has already been reground. FERREA F1920P and F1921P at 35 mm; SUPERTECH VWEVN-1010, VWEVI-1010 and FERREA F2135P at 36 mm. |
| Grooves | 3 grooves SUPERTECH VWEVN-1007 and VWEVN-1010 in black nitrided stainless, VWEVI-1010 in Inconel. They fit with 3-groove collets, for instance the KPR-VW7-T on this page, ideally new when the head is rebuilt. |
1 groove FERREA F1932P and F1920P in Competition Plus, F1921P and F2135P in Super Alloy, the latter being the preferred material once the VR6 is boosted. They require collets made for a single groove, never the original ones. |
When reinforced valves become necessary
- More aggressive camshafts or stiffer valve springs
- Rev ceiling raised as part of the tuning
- Turbo or supercharger fitted to the VR6 (Inconel or Super Alloy preferred)
- Regular circuit or hill climb use
- Head rebuild, burnt or marked exhaust valves
Vehicle compatibility
| Model | Engine code | Power | Years |
|---|---|---|---|
| VW Golf III (1H1) 2.8 VR6 | AAA | 174 hp | 1992-1997 |
| VW Golf III (1H1) 2.8 VR6 | AAA | 163 hp | 1995-1997 |
| VW Vento (1H2) 2.8 VR6 | AAA | 174 hp | 1992-1998 |
| VW Vento (1H2) 2.8 VR6 | AAA | 163 hp | 1992-1998 |
| VW Corrado (53I) 2.8 VR6 | AAA | 174 hp | 1991-1995 |
| VW Passat B3/B4 (3A2, 35I) 2.8 VR6 | AAA | 174 hp | 1991-1996 |
| VW Passat B3/B4 Variant (3A5, 35I) 2.8 VR6 | AAA | 174 hp | 1991-1997 |
| VW Sharan (7M8, 7M9, 7M6) 2.8 VR6 | AAA / AMY | 174 hp | 1995-2000 |
| VW Sharan (7M8, 7M9, 7M6) 2.8 VR6 Syncro | AAA / AMY | 174 hp | 1996-2000 |
| VW Golf IV (1J1) 2.8 VR6 | AFP | 177 hp | 1999-2002 |
| VW Golf IV Variant (1J5) 2.8 V6 | AFP | 177 hp | 2000-2004 |
| VW Bora I (1J2) 2.8 VR6 | AFP | 177 hp | 1998-2005 |
| Ford Galaxy I (WGR) 2.8 i V6 | AAA / AMY | 174 hp | 1995-2000 |
| Ford Galaxy I (WGR) 2.8 i V6 4x4 | AAA / AMY | 174 hp | 1996-2000 |
OEM part number (exhaust valve):
Don't forget the inlet valves
The VR6 2.8 12V head is rebuilt in one go: use the removal to replace its 6 inlet valves and stem seals as well. Here are the ones that suit this engine:
| Inlet valves VW Ford VR6 2.8 12V → |
-
Brand
-
ReferenceVWEVN-1010-6