Skip to content
  • On order
Reinforced inlet valves NISSAN RB25DET RB25DE Reinforced inlet valves NISSAN RB25DET RB25DE

Reinforced inlet valves NISSAN RB25DET RB25DE RB25DEH

€364.35 (tax incl.)
€455.44 (tax incl.) -20%

Set of 12 reinforced inlet valves for NISSAN RB25DET, RB25DE and RB25DEH.

  • Brands: SUPERTECH, FERREA
  • Engines: RB25DET, RB25DE, RB25DEH
  • Dimensions: 34.12 mm to 35.15 mm head, 5.97 mm or 5.98 mm stem, 86.70 mm to 104.20 mm length
  • Material: black nitride stainless steel, stainless steel with chrome stem or special alloy
NIVN-1052-12
0 in stock in France
ORDER TODAY, WE SHIP IN 5 - 15 DAYS
Pay in installments

NISSAN engines covered

The RB25 is Nissan's 2.5 litre 24-valve inline six with twin overhead camshafts, naturally aspirated (RB25DE, RB25DEH) or turbocharged (RB25DET), from 179 to 280 hp. From 1989 to 2006 it powers the Skyline R32, R33 and R34, the Laurel C33, C34 and C35, the Cefiro A31, the Stagea WC34 estate and the Cedric and Gloria Y34.

Its 12 inlet valves come in two cylinder head generations: hydraulic tappets up to June 1997 (Nissan 13201-08U01, superseded by 13201-08U02, 13210-D4200 collets), then the NEO head with solid tappets and shims (13201-5L700, 13201-5L715 then 13201-5L716, 13210-53Y00 collets). More boost, sharper cams or a raised rev limit load them well beyond stock use.

SUPERTECH and FERREA reinforced inlet valves

In an RB25, each of the 12 inlet valves drops under the cam to deliver air to the cylinder, compressed by the turbo on the RB25DET, then climbs back to hit its seat while the stem glides at the heart of the guide; once the six-cylinder winds up, the cycle exceeds twenty strokes a second. The part lives between 400 and 550 °C, when a stock chrome-silicon steel goes from 500 MPa at 500 °C to only 250 MPa at 600 °C: barely above that zone, 50 % of its strength is lost.

At SUPERTECH, a black nitrided layer coats the stainless steel, hardens the stem and spares it where it meets the guide; the stem is also slimmed under the head and the head's rear face is reworked, two machining steps that clear the airflow around the valve. FERREA draws the pieces sold here from its Competition Plus series (stainless, chromed stem), credited with 20 % extra resistance to heat and repeated loads, plus a seat that lasts 25 % longer. The hydraulic-tappet head receives special alloy FERREA valves from this same range.

The three SUPERTECH parts have a 35.15 mm head, at +1 mm, on a 5.97 mm stem. For the NEO head, FERREA lists standard size (34.15 mm) and +1 mm (35.15 mm), 5.98 mm stem, 104.20 mm length; for the hydraulic head, 34.12 mm and 35.12 mm, 5.97 mm stem, 86.70 mm length. A bigger head enlarges the open section at the seat, boosting filling and the six's output, as long as the workshop opens all 12 inlet seats to that diameter.

Inlet valve technical specification

Part numberBrandSizeHead ØStem ØLengthGroovesMaterial
NIVN-1052-12 SUPERTECH +1 mm 35.15 mm 5.97 mm 86.75 mm Black nitride stainless steel
NIVN-1052-NEO-12 SUPERTECH +1 mm 35.15 mm 5.97 mm 104.15 mm Black nitride stainless steel
NIVN-1052-SL-12 SUPERTECH +1 mm 35.15 mm 5.97 mm 103.55 mm Black nitride stainless steel
F1933P*12 FERREA Standard 34.15 mm 5.98 mm 104.20 mm Stainless, chrome stem
F1934P*12 FERREA +1 mm 35.15 mm 5.98 mm 104.20 mm Stainless, chrome stem
F2151P*12 FERREA Standard 34.12 mm 5.97 mm 86.70 mm Special alloy
F2152P*12 FERREA +1 mm 35.12 mm 5.97 mm 86.70 mm Special alloy

NIVN-1052-12: for hydraulic tappet heads; does not fit a NEO cylinder head.

NIVN-1052-NEO-12: for NEO heads with factory solid tappets.

NIVN-1052-SL-12: 16.8 mm longer, for a solid tappet conversion; groove placed 10 mm higher, 11.5 mm stem tip; does not fit a NEO cylinder head.

F1933P*12 and F1934P*12: for NEO heads, 6.25 mm stem tip.

F2151P*12 and F2152P*12: for hydraulic tappet heads, 3.5 mm stem tip.

Fitting details

PartNISSAN originalReinforced
Collets 13210-D4200 / 13210-53Y00 (NEO) KPR-6N-6-ST-24
Valve stem seals 13207-84A00 / 13207-D4201 / 13207-5L300 (NEO) VS-N6I-12
Valve guide 13212-58S60 GDE-NSR6-I-12

The +1 mm oversize needs the inlet seats cut to 35.15 mm, workshop work to plan with the cylinder head rebuild.

The length follows the cylinder head: 86.75 mm (SUPERTECH) or 86.70 mm (FERREA) on a hydraulic tappet head, 104.15 mm (SUPERTECH) or 104.20 mm (FERREA) on a NEO head, 103.55 mm to convert a non-NEO head to solid tappets.

On a NEO head or one converted to solid tappets, check the clearance after replacing the valves and adjust the shims.

Technical guide

Our brands

SUPERTECH SUPERTECH Performance: a name built over more than thirty years in San Jose around competition valves, springs and retainers. Its teams tune each part number on a real cylinder head alongside engine builders, then check it with ultrasound, X-rays and laser.
FERREA FERREA Racing Components owes its birth, in 1978, to two engine builders from Argentina, who opened the workshop in Fort Lauderdale (Florida). The firm forges each valve in a single piece from bar, finishes it entirely on numerical machining centres and sees it compete in NASCAR and dragsters.

How to choose

First identify the head and its tappets, which dictate the valve length; the size then depends on how the inlet seats look and on the extra filling wanted.

CriterionOption 1Option 2
Cylinder head Hydraulic tappets
Head made up to June 1997: NIVN-1052-12, length 86.75 mm.
NEO
NEO head, solid tappets from the factory: NIVN-1052-NEO-12, length 104.15 mm.
Tappets Hydraulic kept
Non-NEO head left in its stock layout: NIVN-1052-12.
Solid conversion
Non-NEO head switched to solid tappets: NIVN-1052-SL-12, 103.55 mm, groove 10 mm higher.
Size Standard size
34.12 mm head (F2151P*12, hydraulic head) or 34.15 mm (F1933P*12, NEO head), when the seats have not moved since the factory.
+1 mm oversize
35.12 mm head (F2152P*12) or 35.15 mm (F1934P*12 and SUPERTECH): roughly 10 to 12 cfm won for every mm of head. Seats need recutting; a valid route for seats that were reground before.

When reinforced valves become necessary

  • Boost raised beyond the factory setting
  • Reground camshafts or springs rated higher
  • Rev limiter moved up
  • Engine bound for drift, circuits or stages
  • Weary stock valves or seat faces already reground

Compatible vehicles

ModelEngine codePowerYears
Skyline (R32) 2.5 RB25DE 179 hp 1989-1993
Skyline (R33) 2.5 / 2.5 4x4 RB25DE 190 hp 1993-1998
Skyline Coupé (R33) 2.5 (ECR33) RB25DET 250 hp 1994-2000
Skyline (R34) 2.5 / 2.5 4x4 RB25DEH 200 hp 1998-2000
Skyline (R34) 2.5 / 2.5 Turbo RB25DET 254-280 hp 1998-2006
Laurel (C33) 2.5 i RB25DE 190 hp 1991-1992
Laurel (C34) 2.5 i / 2.5 i 4x4 RB25DE 190 hp 1993-1997
Laurel (C34) 2.5 i Turbo / Turbo 4x4 RB25DET 234 hp 1993-1997
Laurel (C35) 2.5 i / 2.5 i 4x4 RB25DE 200 hp 1997-2002
Laurel (C35) 2.5 i Turbo / Turbo 4x4 RB25DET 234-280 hp 1997-2002
Cefiro I (A31) 2.5 RB25DE 180 hp 1992-1994
Stagea (WC34) 2.5 / 2.5 AWD RB25DE 190 hp 1996-2001
Stagea (WC34) 2.5 Turbo AWD RB25DET 235 hp 1996-2001
Cedric X (Y34) 2.5 AWD / 2.5 Turbo 4WD RB25DET 250-260 hp 1999-2004
Gloria XI (Y34) 2.5 AWD / 2.5 Turbo 4WD RB25DET 250-260 hp 1999-2004

OEM part number (inlet valve): 13201-08U01 / 13201-08U02 ; NEO : 13201-5L700 / 13201-5L715 / 13201-5L716

Important: the three lengths are not interchangeable, the cylinder head decides the part number; the RB20DET and RB26DETT are not included.

Related products

An opened RB25DET head is ideally closed with new exhaust valves too; the pages below list their reinforced versions for this engine:

NISSAN RB25DET exhaust valves →
NISSAN Skyline R34 RB25DET NEO exhaust valves →

16 other products in the same category

Viewed products

Loading...