Skip to content
  • On order
Reinforced inlet valves MAZDA MX-5 323 6 BP L8 1.8 Reinforced inlet valves MAZDA MX-5 323 6 BP L8 1.8

Reinforced inlet valves MAZDA MX-5 323 6 BP L8 1.8

€221.92 (tax incl.)
€277.40 (tax incl.) -20%

Set of 8 reinforced inlet valves for MAZDA MX-5, 323, 5 and 6 BP and L8 1.8.

  • Brand: SUPERTECH
  • Engines: BP 1.8 16V naturally aspirated and turbo (BP-ZE, BPD, BP5A, BP6J, BP4W, BP8K), L8-DE, L8-VE
  • Dimensions: 33 mm or 34 mm head, 5.97 or 5.96 mm stem, 102 mm long
  • Material: black nitride stainless steel
MAIVN-1204-8
0 in stock in France
ORDER TODAY, WE SHIP IN 5 - 15 DAYS
Pay in installments

MAZDA engines covered

The BP is Mazda's 1.8-litre four-cylinder with twin camshafts and 16 valves, naturally aspirated or turbocharged: it powers the 323 BG from 1989 to 1994, including the four-wheel-drive turbos and the GT-R, then the 323 BA and BW, the MX-5 NA from 1993 and the NB up to 2005. The 1.8-litre L8-DE and L8-VE takes over in the MX-5 NC, the Mazda 5 and the Mazda 6.

Each of these engines uses 8 inlet valves, two per cylinder. Raised boost, sharper cams or a higher rev limit expose them to far more heat and impact than the standard engine.

SUPERTECH reinforced inlet valves

On every lift this valve admits the fresh charge, strikes its seat on the way back and keeps sliding against the guide. It heats up to 400 to 550 °C, where ordinary chrome-silicon steel weakens: 500 MPa at 500 °C, but only 250 MPa at 600 °C, a 50 % loss of strength. On a tuned engine each of these stresses grows.

SUPERTECH cuts them from stainless steel before a black nitride treatment: the hardened surface resists galling and the stem wears less in its guide. At standard size two designs exist, high flow or standard flow; at +1 mm, two seat face variants, stellite seat or extra hardened seat.

At +1 mm oversize the head goes from 33 to 34 mm with the length unchanged. More air gets past the bigger seat opening, cylinder filling goes up and so does output, once all 8 inlet seats have been machined to suit.

Inlet valve technical specification

Part numberBrandSizeHead ØStem ØLengthGroovesMaterial
MAIVN-1204-8 SUPERTECH Standard 33 mm 5.97 mm 102 mm Black nitrided stainless steel
MAIVN-1208-8 SUPERTECH Standard 33 mm 5.97 mm 102 mm Black nitrided stainless steel
MAIVN-1206-8 SUPERTECH +1 mm 34 mm 5.97 mm 102 mm Black nitrided stainless steel
MAIVN-1206-HN-8 SUPERTECH +1 mm 34 mm 5.96 mm 102 mm Black nitrided stainless steel

MAIVN-1204-8: high flow, thinned under the head and profiled on the back. MAIVN-1208-8: standard flow. MAIVN-1206-8: +1 mm, stellite seat. MAIVN-1206-HN-8: +1 mm, extra hardened seat, 5.96 mm stem.

Fitting details

PartMAZDA originalReinforced
Collets
Valve stem seals VS-TS6I-8
Valve guide

The VS-TS6I-8 inlet valve stem seals are made for the 6 mm stem of these valves.

With a 33 mm head the inlet seats keep their factory size; with 34 mm the workshop recuts all 8 seats before reassembly.

Technical guide

The brand offered

SUPERTECH The Californian specialist SUPERTECH Performance has produced valves, springs and guides reserved for motorsport for some thirty years. Its parts are examined with ultrasound, radiography and laser, then shipped to the tuners who assemble racing engines.

How to choose

The groove is the notch near the stem tip into which the collets fit to hold the upper retainer. For these engines, pick the head size first, then the version.

CriterionOption 1Option 2
Size Standard, 33 mm
Seats at factory dimension. MAIVN-1204-8 (high flow), MAIVN-1208-8 (standard flow).
+1 mm, 34 mm
Roughly 10 to 12 cfm better per mm of head, with the seats recut; also suits seats already reworked. MAIVN-1206-8, MAIVN-1206-HN-8.
Seat (+1 mm) Stellite seat
MAIVN-1206-8.
Extra hardened seat
MAIVN-1206-HN-8.

When reinforced valves become necessary

  • Bigger turbo or higher boost pressure
  • Wilder cam profiles, stiffer valve springs
  • Rev limit raised through an ECU remap
  • Cylinder head rebuilt for circuit racing or rallies
  • Tired Mazda valves, seats recut in a rebuild

Compatible vehicles

ModelEngine codePowerYears
323 C IV (BG) 1.8 16V 4WD, Turbo 4WD, GT-R 4WD BP / BP Turbo 103-209 hp 1989-1994
323 S IV (BG) 1.8 16V Turbo 4WD BP Turbo 163 hp 1991-1994
323 C V, 323 F V (BA) 1.8 16V BP-ZE 114-135 hp 1994-1998
323 S V (BA) 1.8 16V BP-ZE 114 hp 1994-1998
323 III Station Wagon (BW) 1.8 BPF1 125 hp 1992-1998
MX-5 I (NA) 1.8 BP-ZE / BPF1 130-135 hp 1993-1998
MX-5 II (NB) 1.8, 1.8 16V, 1.8 i BPD / BP5A / BP6J / BP-ZE / BP4W 139-154 hp 1998-2005
MX-5 II (NB) 1.8 SE i Turbo, 1.8 i Turbo BP Turbo / BP8K 165-214 hp 2002-2005
MX-5 III (NC) 1.8 (NC18) L8-DE / L8-VE 126 hp 2005-2014
Mazda 5 (CR) 1.8 (CR19) L8-VE 116 hp 2005-2010
Mazda 6 (GG) 1.8 L8-DE / L8-VE 120 hp 2002-2007
Mazda 6 Station Wagon (GY) 1.8 L8-DE 120 hp 2002-2007
Mazda 6 (GH) 1.8 MZR L8-DE 120 hp 2007-2013
Important: a set of 8 covers a complete engine. The L828, with an original 5.5 mm valve stem, and the MX-5 1.6 B6 use different valves.

Don't forget the exhaust valves

With the head off, replace the 8 exhaust valves at the same time together with the inlet valve stem seals; all of them are offered here:

MAZDA MX-5 1.8 BP exhaust valves →
MAZDA MX-5 323 B6 BP inlet valve stem seals →

16 other products in the same category

Viewed products

Loading...