- On order
Reinforced exhaust valves BMW M3 E36 Z3M S50B32
Set of 12 reinforced exhaust valves for the BMW S50B32.
- Brand: SUPERTECH
- Engine: S50B32 (M3 E36 3.2, Z3 M)
- Dimensions: standard head or 31 mm, 6 mm stem
- Material: black nitride finish or Inconel, 3 grooves or single groove
BMW engines covered
The European 3.2 litre version of the S50 straight six, the S50B32 displaces 3,201 cc (86.4 mm bore, 91 mm stroke) and was built from 1995 to 2001. It powers the M3 E36 3.2 and the Z3 M.
Its 24 valves are operated by solid tappets with adjusting shims. The 12 BMW exhaust valves have a 30.5 mm head and a 6 mm stem, held by 3-groove collets; on an engine so often revved hard, on the road as on track, they take the full blast of the gases leaving the chamber.
SUPERTECH reinforced exhaust valves
Opening just as the gases leave the chamber, the exhaust valve takes most of the combustion heat. On this naturally aspirated six its head works between 760 and 870 °C; boost takes it past 1,000 °C. It has only two ways to cool down: the seat, through which around 75 % of that heat passes, then the guide, for about 20 %. The original steel is assessed with EV8 family figures: 550 MPa at 600 °C, barely 300 MPa at 800 °C. Once load, revs or pressure climb, the head overheats, gives in to fatigue, distorts and then leaks.
The BMEVN-1037 stays in high temperature stainless steel but gets black nitriding: its stem, harder and smoother, slides in the guide with less friction and wears more slowly. The BMEVI-1030PSL switches to Inconel, a nickel superalloy keeping 860 MPa at 732 °C and still 554 MPa at 816 °C; near 800 °C the gap reaches about 85 % in its favour over EV8 steel. Supercharger or turbo on the cards: this is the one to choose, as it holds its strength where stainless steel gives way.
On the same BMEVI-1030PSL the head grows from 30.5 to 31.0 mm. That half millimetre opens a wider path to burnt gases: the chamber clears sooner, a larger fresh charge follows on the next turn, hence extra power. It is also 122.8 mm long, against 121.3 mm for the BMEVN-1037, and has a single groove. In return, the cylinder head has its exhaust seats recut to 31 mm.
Exhaust valve technical specifications
| Part number | Brand | Size | Head Ø OEM 30.5 mm | Stem Ø OEM 6 mm | Length | Grooves | Material |
|---|---|---|---|---|---|---|---|
| BMEVN-1037-12 | SUPERTECH | Standard | 30.5 mm | 6 mm | 121.3 mm | 3 | Black nitrided stainless |
| BMEVI-1030PSL-12 | SUPERTECH | +0.5 mm | 31.0 mm | 6 mm | 122.8 mm | 1 | Inconel |
Valve fitting
| Part | BMW original | Reinforced |
|---|---|---|
| Collets | 11 34 1 461 405 (3 grooves) | KPR-VW6-T (3 grooves) / KPR-6S-7 (1 groove) |
| Valve stem seals | kit 11 34 9 064 457 | VS-VBM6E-12 (exhaust) |
| Valve guide | 11 12 1 315 999 |
The number of grooves decides the collets: the BMEVN-1037, with 3 grooves like the BMW part, takes the KPR-VW6-T; the single groove BMEVI-1030PSL is fitted with the KPR-6S-7.
With the BMEVN-1037 the exhaust seats stay at their size; the 31.0 mm of the BMEVI-1030PSL require them to be recut to that size before fitting.
For stem sealing, these valves are fitted with VS-VBM6E-12 exhaust valve stem seals.
Technical guide
Our brand
| SUPERTECH Performance was born in Silicon Valley and has built racing head parts for more than thirty years, from valves to titanium spring retainers. Offered in stainless steel, titanium and Inconel, its valves are developed engine by engine and then validated by tuners from drag racing, rally and circuit work. |
How to choose
Clamped by the spring retainer, the collets take hold of the stem and immobilise the valve. With one groove or with three, its retention is not the same, and neither is the advantage you find in it:
| Criterion | Option 1 | Option 2 |
|---|---|---|
| Size | Standard 30.5 mm head, identical to the BMW part: it sits on intact exhaust seats, without any visit to a machining shop. The only finish at this size: stainless steel with black nitriding, its hardened stem standing up better to wear. |
+0.5 mm, 31.0 mm With an enlarged head, burnt gases escape earlier and the chamber fills more on the next cycle: a lever for power. Seats are recut to 31 mm, which also rescues seats already reworked. Inconel only, the version for boosted engines. |
| Grooves | 3 grooves The BMW architecture is kept, the stem turning freely between its collets. Nothing else to change on an engine kept near stock, except new collets (KPR-VW6-T) as a precaution. Limit: if the valve is hit as it closes, the lower groove, the thinnest, takes the blow. |
Single groove Here the collets pinch the stem: the groove hardly works any more and the larger contact area limits friction. The result is a sturdier valve when springs are hard, lift is big and revs are high. KPR-6S-7 collets mandatory, preferably new. |
When reinforced valves become necessary
- More aggressive cam profiles or harder valve springs
- Rev limiter moved higher
- Supercharger or turbo added (Inconel then the better choice)
- Head rebuild aimed at circuit, drift or rally
- Original valves damaged, tired or down to repair size
Vehicle compatibility
| Model | Engine code | Power | Years |
|---|---|---|---|
| M3 (E36) 3.2 | S50B32 | 321 hp | 1995-1999 |
| Z3 M (E36) 3.2 | S50B32 | 321 hp | 1997-2001 |
OEM part number (exhaust valve): 11 34 1 404 589
Don't forget the inlet valves
With the S50B32 cylinder head open, the inlet valves can be renewed too, with no extra dismantling at all. Here is the matching part for this engine:
| BMW M3 E36 Z3M S50B32 inlet valves → |
-
Brand
-
ReferenceBMEVN-1037-12