Skip to content
  • On order
Reinforced inlet valves SUPERTECH BMW S50B32 Reinforced inlet valves SUPERTECH BMW S50B32

Reinforced inlet valves SUPERTECH BMW S50B32

€460.92 (tax incl.)
€576.16 (tax incl.) -20%

Set of 12 reinforced inlet valves for BMW S50B32.

  • Brand: SUPERTECH
  • Engine: S50B32
  • Dimensions: 35 mm or 35.65 mm head, 6 mm stem
  • Material: stainless steel, 1 or 3 grooves
BMIVN-1037-12
On order, 15 to 30 days lead time
Pay in installments

BMW engines covered

The S50B32 is the 3.2 litre, 24-valve inline six-cylinder petrol engine, in its European version, of the BMW M3 3.2 E36 (saloon, coupe and convertible) and of the Z3 M roadster and Z3 M coupe.

It has 12 inlet valves, BMW part number 11 34 1 404 588: 35.0 mm head, 6.0 mm stem, held by 3-groove collets and operated by mechanical tappets with shims. Designed for the standard engine, they reach their limits as soon as sharper camshafts, stiffer springs, higher revs or forced induction are fitted.

SUPERTECH reinforced inlet valves

On an S50B32 spinning hard, each inlet valve frees the fresh air path and then plugs it again, dozens of times before a second has gone by. Every time it closes, the head taps the cut seat in the head casting; between closings, the stem keeps gliding in the guide. Operating temperature runs from 400 to 550 °C, the very zone where the original chrome-silicon steel is already weakening: 500 MPa at 500 °C, then 250 MPa from 600 °C, just above, which strips 50 % of its strength. Seeking higher lift, harder springs, extra revs or more turbo pressure always costs the valve additional shocks, friction and heat.

The SUPERTECH reinforced valves on this page come out of a forge in chrome-nickel stainless steel designed for racing, related to EV8 (21-4N). At 500 °C this steel still holds 650 MPa, 30 % above the production one; at 600 °C it keeps 550 MPa, 120 % above. Thanks to black nitriding the valves get a surface both harder and smoother, sparing the stem in its guide by limiting friction and wear.

A +0.65 mm oversize version is offered too: the head goes from 35.0 to 35.65 mm, the 6 mm stem does not change. The seat passes a larger flow, the cylinder breathes more freely and output goes up, as long as the head seats are recut to this new diameter.

Inlet valve technical specifications

Part numberBrandSizeHead Ø
OEM 35.0 mm
Stem Ø
OEM 6 mm
LengthGroovesMaterial
BMIVN-1037-12 SUPERTECH Standard 35.0 mm 6 mm 119.75 mm 3 Black nitrided stainless
BMIVN-1033SL-12 SUPERTECH +0.65 mm 35.65 mm 6 mm 121.3 mm 1 Black nitrided stainless

Valve fitting

PartBMW originalReinforced
Valve collets 11 34 1 461 405 (3 grooves) KPR-VW6-T (3 grooves) / KPR-6S-7 (1 groove)
Valve stem seals Kit 11 34 9 064 457 VS-VBM6I-12 (inlet)
Valve guide 11 12 1 315 999

Each valve type has its own collets: SUPERTECH pairs its KPR-VW6-T collets with its 3-groove valves and its KPR-6S-7 collets with its single groove valves. A single groove valve never takes the original collets.

The +0.65 mm version needs cylinder head seats cut to the diameter of the new head, to be planned with the cylinder head rebuild.

The S50B32 has mechanical tappets with shims: after replacing the valves, check the clearance and adjust the shims.

Technical guide

The brand offered

SUPERTECH SUPERTECH has been designing racing valvetrain hardware for more than 30 years in its San Jose workshops, California. Each valve is calculated for a given engine, probed by ultrasound, X-rayed, laser-measured, then confirmed by engine builders, in drag racing as on circuits.

How to choose

The groove is the recess in the stem where the collets sit, under the retainer. Its profile decides how the valve is retained, and so what loads it copes with.

CriterionOption 1Option 2
Size Standard size
35.0 mm head, as on the BMW valve: the one to fit while inlet seats keep their ex-factory size.
+0.65 mm oversize
35.65 mm head: wider seat, more air drawn in, hence more power. Head seats are to be recut to this new size, ideally with enlarged ports; handy too for seats ground in an earlier rebuild.
Grooves 3 grooves
Shape chosen by BMW, the stem can spin freely. Suits road use, with springs and revs near stock; new collets recommended (original or KPR-VW6-T). Drawback: at high revs the bottom groove takes the impacts, although it is the thinnest section.
Single groove
Clamped by its collets, the stem barely bears on the groove any more, and the wider contact cuts friction. The valve becomes tougher and copes with uprated springs, big lift and a high rev ceiling. SUPERTECH's pick for high output, on track, drifting, rallying or drag racing. KPR-6S-7 collets essential, ideally new.

When reinforced valves become necessary

  • High-lift camshafts or punchier springs
  • Rev cut moved further up
  • Engine given a turbo or supercharger
  • Head rebuilt for circuit, drift or rally
  • Factory valves damaged, tired or brought to repair size

Vehicle compatibility

ModelEngine codePowerYears
M3 3.2 (E36) S50B32 321 hp 1995-1998
M3 3.2 Coupe (E36) S50B32 321 hp 1995-1998
M3 3.2 Convertible (E36) S50B32 321 hp 1996-1999
Z3 M 3.2 Roadster (E36) S50B32 321 hp 1997-2000
Z3 M Coupe (E36) S50B32 321 hp 1998-2001

OEM part number (inlet valve): 11 34 1 404 588

Important: these valves fit neither the European S50B30 of the M3 3.0 E36, whose valve stem is 7 mm, nor the American S52B32, whose inlet head is 33.0 mm.

Don't forget the exhaust valves

When an S50B32 head is restored, the exhaust valves and all the valve stem seals are usually replaced at the same time. New parts suited to this engine:

BMW S50B32 exhaust valves →
6 mm inlet valve stem seals →

13 other products in the same category

Viewed products

Loading...