- In stock
Reinforced inlet valves VAG Golf R32 TT A3 3.2 VR6
Sets of 12 reinforced inlet valves, 6 long and 6 short, for the VAG group 3.2 VR6: VOLKSWAGEN Golf 4 R32, Golf 5 R32 and Eos 3.2, AUDI TT 8N, TT 8J and A3 8P 3.2 quattro.
- Brands: SUPERTECH, FERREA
- Engines: BFH, BML, BJS, BHE, BPF, BUB, CBRA
- Dimensions: 33.15 mm, 33.2 mm or 34.2 mm head
- Material: black nitride stainless steel, single groove (SUPERTECH); FERREA Competition Plus
VAG engines covered
The 3.2 litre VR6 is the Volkswagen group (VAG) 24 valve six-cylinder, a very narrow-angle V under a single cylinder head. At Volkswagen it powers the Golf IV R32 from 2002 to 2005 (241 hp), then the Golf V R32 and the Eos 3.2 from 2005 to 2009 (250 hp). At Audi it drives, with 250 hp, the TT 8N coupé and roadster from 2003 to 2006 (BHE, BPF), the A3 8P and A3 Sportback from 2003 to 2009 (BUB), then the TT 8J coupé and roadster from 2006 to 2010 (BUB, CBRA), all quattro.
The head takes 12 inlet valves of two lengths: 6 long VW 022 109 601 H and 6 short 022 109 601 G, with a 33.2 mm head and 6 mm stem. Each set offered here therefore combines 6 long and 6 short valves. Sharper camshafts, higher revs or forced induction load them far beyond standard use.
SUPERTECH and FERREA reinforced inlet valves
On the 24-valve VR6 3.2, twelve inlet valves, two per cylinder, meter the fresh air entering the chambers. Under full load each valve springs off its seat and crashes down again dozens of times a second, its stem meanwhile shuttling up and down inside the guide. Working temperature sits at 400 to 550 °C, a range where standard chrome-silicon steel already gives way: 500 MPa at 500 °C, yet only 250 MPa at 600 °C, just past it, so 50 % lost. Raise the lift, stiffen the springs, rev the VR6 harder or bolt on a turbo, and impacts, friction wear and heat climb together.
SUPERTECH valves are cut from a chrome-nickel racing stainless close to EV8 (21-4N): it retains 650 MPa at 500 °C, 30 % more than the standard steel, and 550 MPa at 600 °C, 120 % more. Black nitriding leaves the stem tougher and slicker, cutting friction and wear in the guide, and the stem is also undercut below the head. The FERREA parts come from its Competition Plus line, rated by the brand 20 % stronger when hot and in fatigue, with seats lasting 25 % longer, and carry a chromed stem.
FERREA also offers them in +1 mm oversize: the head grows to 34.2 mm instead of 33.2 mm, while the 6 mm stem and both lengths stay the same. With that bigger diameter the seat opening widens, the cylinders fill more easily and power goes up, on condition that the VR6 inlet seats get recut to suit.
Inlet valve technical specification
| Part number | Brand | Size | Head Ø OEM 33.2 mm | Stem Ø OEM 6 mm | Length OEM 102.4 / 136.3 mm | Grooves | Material |
|---|---|---|---|---|---|---|---|
| VWIVN-1044SL | SUPERTECH | Standard | 33.15 mm | 5.97 mm | 136.4 mm | 1 | Black nitride stainless steel |
| VWIVN-1044SS | SUPERTECH | Standard | 33.15 mm | 5.97 mm | 102.5 mm | 1 | Black nitride stainless steel |
| F2292P | FERREA Competition Plus | Standard | 33.2 mm | 5.98 mm | 136.7 mm | Stainless, chrome stem | |
| F2293P | FERREA Competition Plus | Standard | 33.2 mm | 5.98 mm | 102.8 mm | Stainless, chrome stem | |
| F2294P | FERREA Competition Plus | +1 mm | 34.2 mm | 5.98 mm | 136.7 mm | Stainless, chrome stem | |
| F2295P | FERREA Competition Plus | +1 mm | 34.2 mm | 5.98 mm | 102.8 mm | Stainless, chrome stem |
Sold in sets of 6 long and 6 short valves: VWIVN-1044SL-6+VWIVN-1044SS-6, F2292P*6+F2293P*6, F2294P*6+F2295P*6.
VWIVN-1044SL and VWIVN-1044SS: undercut stem under the head.
FERREA part numbers intended for the VW VR6 R32 3.2 DOHC 24 valve (2004-2011) and the Audi TT VR6 3.2 DOHC 24 valve, BHE and CBRA engines.
Fitting details
| Part | Original | Reinforced |
|---|---|---|
| Collets | KPR-6S-7-24 (1 groove) | |
| Valve stem seals | 036 109 675 A | |
| Valve guide |
The +1 mm size needs the inlet seats cut to 34.2 mm, a workshop job to plan with the cylinder head rebuild.
The 3.2 VR6 takes up valve clearance with hydraulic tappets: no adjustment is needed after replacing the valves.
Technical guide
Our brands
| From its San Jose base in California, SUPERTECH has supplied racing with valvetrain hardware for over 30 years. Every valve design is drawn for one specific head, checked piece by piece by laser, X-ray and ultrasound, and approved with engine builders in drag racing and on circuits. | |
| Two Argentine-born engine builders started FERREA Racing Components back in 1978 in Fort Lauderdale, Florida, where manufacturing stays entirely in house. Its valves are forged in one go from bar stock, fully CNC-machined, and are found in NASCAR, drag events and circuit racing. |
How to choose
Collets sit in the stem groove under the retainer, and that is where they grip the valve. Choose the size from your seats, then the material from the use.
| Criterion | Option 1 | Option 2 |
|---|---|---|
| Size | Standard size, 33.2 mm For a VR6 head with all 12 inlet seats untouched since the factory: direct fit, no machining, with the 6 mm stem and VW's 102.4 and 136.3 mm lengths. From SUPERTECH (33.15 mm) and FERREA, for a rebuild true to original. |
+1 mm oversize, 34.2 mm Larger seat opening, so more air drawn in and more power, roughly 10 to 12 cfm of added flow per millimetre of head. Recut seats to the bigger diameter, ideally with port work; this size can also save previously reground seats. FERREA only. |
| Material | Stainless, chromed stem Competition Plus line from FERREA: 20 % more heat and fatigue strength, seats lasting 25 % longer. For a hard-worked VR6, turbo or high revs, on circuit, hillclimb or rally, when the head is rebuilt to last. |
Black nitrided stainless, single groove SUPERTECH: surface-hardened stem with lower friction against the guide and slower wear; on a single groove the collets clamp the stem and relieve the groove. KPR-6S-7-24 single-groove collets mandatory, preferably new; suits road and track. |
When reinforced valves become necessary
- More aggressive camshaft profiles or stiffer springs
- Rev limit pushed higher
- Turbo or supercharger fitted to the VR6
- VR6 head redone for circuit, drift or rally
- Tired, damaged or repair-size original VW valves
Compatible vehicles
| Model | Engine code | Power | Years |
|---|---|---|---|
| AUDI A3 (8P1) 3.2 V6 quattro | BUB | 250 hp | 2003-2009 |
| AUDI A3 Sportback (8PA) 3.2 V6 quattro | BUB | 250 hp | 2004-2009 |
| AUDI TT (8N3) 3.2 VR6 quattro | BHE / BPF | 250 hp | 2003-2006 |
| AUDI TT Roadster (8N9) 3.2 VR6 quattro | BHE / BPF | 250 hp | 2003-2006 |
| AUDI TT (8J3) 3.2 V6 quattro | BUB / CBRA | 250 hp | 2006-2010 |
| AUDI TT Roadster (8J9) 3.2 V6 quattro | BUB / CBRA | 250 hp | 2007-2010 |
| VW Golf IV R32 4motion (1J1) | BFH / BML / BJS | 241 hp | 2002-2005 |
| VW Golf V R32 4motion (1K1) | BUB / CBRA | 250 hp | 2005-2008 |
| VW Eos 3.2 V6 (1F7, 1F8) | BUB / CBRA | 250 hp | 2006-2009 |
OEM part number (inlet valve): 022 109 601 H (long), 022 109 601 G (short)
Related products
Before closing up the VR6 head, also plan reinforced exhaust valves and new valve stem seals. The exhaust valve page for these engines:
| VW Golf 4 Golf 5 R32 3.2 24V exhaust valves → |
-
Brand
-
ReferenceVWIVN-1044SL-6+VWIVN-1044SS-6
-
In stock1 Item