- On order
Reinforced inlet valves MAZDA FORD FS
Set of 8 reinforced inlet valves for MAZDA and FORD FS.
- Brand: SUPERTECH
- Engines: FS, FS2C, FSZE 2.0 16V
- Dimensions: 32.5 mm head, 5.97 mm stem, 89.9 mm long
- Material: black nitride EV8 stainless steel
MAZDA engines covered
Mazda built the FS, a 2 litre four-cylinder with 16 valves and twin camshafts, also offered in the stronger FS2C and FSZE variants. Between 1991 and 2006 it is found in the 626 GE and GF, the MX-6, the 323 BJ, the Premacy and the MPV, from 115 to 170 hp, as well as in the Ford Telstar 2.0 i from 1993 to 1999.
The engine has 8 inlet valves, two per cylinder. Sharper cam profiles, stiffer springs or a raised red line load them far beyond everyday driving.
SUPERTECH reinforced inlet valves
In charge of letting fresh air through, the inlet valve never rests: it lifts, snaps shut on its seat and moves back and forth in its guide. It operates between 400 and 550 °C. A standard chrome-silicon steel keeps only 250 MPa at 600 °C against 500 MPa at 500 °C, half of its strength, 50 % lost.
For the MAIVN-2002, SUPERTECH uses EV8 stainless steel: 650 MPa at 500 °C and 550 MPa at 600 °C, beating chrome-silicon steel by 30 % then 120 %. Black nitriding hardens the outside and shields the stem from friction in its guide.
It comes in +1 mm size: 32.5 mm head, 5.97 mm stem, 89.9 mm length. Air crosses a wider seat, filling improves and power follows, provided the 8 inlet seats are cut to that size.
Inlet valve technical specification
| Part number | Brand | Size | Head Ø | Stem Ø | Length | Grooves | Material |
|---|---|---|---|---|---|---|---|
| MAIVN-2002-8 | SUPERTECH | +1 mm | 32.5 mm | 5.97 mm | 89.9 mm | Black nitrided EV8 stainless |
MAIVN-2002-8: set of 8 valves in +1 mm, hollow head.
Fitting details
| Part | MAZDA original | Reinforced |
|---|---|---|
| Collets | ||
| Valve stem seals | VS-T6SM-8 | |
| Valve guide | GDE-MA20FS-8 |
The 8 inlet seats are recut to 32.5 mm before the valves are fitted.
Reuse sound collets matching the valve groove profile, and check they seat properly before releasing each spring.
Technical guide
The brand offered
| Established in California, SUPERTECH Performance has spent three decades designing valves, springs and guides for motorsport. Its batches are checked by X-ray, ultrasound and laser measurement before going into circuit, rally, hill climb or drag engines. |
How to choose
For the FS, a single part number is listed here: its size and treatment show the head preparation to plan and the benefit over the Mazda factory valve.
| Criterion | Option offered |
|---|---|
| Size | +1 mm size 32.5 mm head, i.e. 10 to 12 cfm gained for each extra mm; seats are recut, which also saves seats already ground. |
| Finish | Black nitrided EV8 stainless Hardened outer skin: the stem wears less against the guide and the valve keeps more strength when hot than the stock part. |
When reinforced valves become necessary
- Aggressive camshafts and uprated valve springs
- Fuel cut set higher than stock
- Turbocharger or supercharger conversion
- Cylinder head prepared for competition
- Damaged Mazda valves or seats ground during a rebuild
Compatible vehicles
| Model | Engine code | Power | Years |
|---|---|---|---|
| 626 IV (GE) 2.0 i | FS | 115-116 hp | 1991-1997 |
| 626 III Station Wagon (GV) 2.0 GLX | FS | 117 hp | 1992-1995 |
| MX-6 (GE) 2.0 | FS | 115 hp | 1992-1997 |
| 626 V (GF) 2.0 | FS / FS2C / FSZE | 115-170 hp | 1997-2006 |
| 626 V Station Wagon (GW) 2.0 | FS / FS2C | 116-136 hp | 1998-2002 |
| 323 VI (BJ) 2.0 | FS / FSZE / FS7E | 131-170 hp | 1998-2004 |
| MPV II (LW) 2.0 | FS | 120-135 hp | 1999-2006 |
| Premacy (CP) 2.0 | FSZE | 165 hp | 2001-2005 |
| Ford Telstar 2.0 i | FS | 1993-1999 |
OEM part number (inlet valve):
Don't forget the exhaust valves
With the FS head off, it makes sense to change its 8 exhaust valves too: a reinforced version, built for the same engine, can be found here:
| MAZDA 323 626 MX-6 2.0 FS exhaust valves → |
| SUPERTECH bronze valve guides Mazda Ford FS 2.0 16V → |
-
Brand
-
ReferenceMAIVN-2002-8