Skip to content
  • On order
Reinforced exhaust valves Renault Megane II RS F4Rt Reinforced exhaust valves Renault Megane II RS F4Rt

Reinforced exhaust valves Renault Megane II RS F4Rt

€345.92 (tax incl.)
€432.40 (tax incl.) -20%

Set of 8 reinforced exhaust valves for the Renault Megane II RS.

  • Brand: SUPERTECH
  • Engine: F4Rt 774 2.0 16V turbo
  • Dimensions: 29 mm or 30 mm head, 5.97 mm stem
  • Material: Inconel, single groove
REVI-28338FS-3-6-8
On order, 15 to 30 days lead time
Pay in installments

Renault engines covered

The F4Rt 774 is the turbo version of Renault's 2 litre, 16-valve F4R four-cylinder; it powers the Megane II Renault Sport from 2004 to 2009.

It has 8 exhaust valves, two per cylinder. The original valve (13202-00QAE) has a 29 mm head and a 5.5 mm stem; turbocharging exposes it to hotter gases than on the naturally aspirated versions.

SUPERTECH reinforced exhaust valves

The F4Rt 774 of the Mégane II Renault Sport, a 2-litre turbo four with 16 valves, puts its 8 exhaust valves through a harsh thermal regime: under boost the head goes beyond 1,000 °C, where a naturally aspirated engine stays between 760 and 870 °C. Heat leaves almost entirely by contact: the seat removes roughly 75 % of the heat, the guide close to 20 %. A steel treated as EV8 sees its strength slide from 550 MPa at 600 °C to 300 MPa at 800 °C; past that, the head heats up, wears, twists and loses its seal.

For this block SUPERTECH chooses Inconel, a superalloy in which nickel dominates. It keeps 860 MPa near 730 °C and 554 MPa near 815 °C, about 85 % above the original steel around 800 °C: it is the material that imposes itself as soon as raised boost drives gas temperatures up. Both parts adopt a single groove and a 5.97 mm stem, reduced to 5.5 mm at its tip, for a length of 108.9 mm. That slimmed tip calls for specific collets, the KPR-6S-7, in place of the Renault parts.

The REVI-28338FS-2-6-8 keeps a 29 mm head, as on the Renault part, while the REVI-28338FS-3-6-8 moves to 30 mm, that is +1 mm. The larger diameter lets burnt gases out earlier, clears the chamber and offers more volume to the next charge, which turns into power. With the latter, the exhaust seats are machined to 30 mm before reassembly, on a head in sound condition.

Exhaust valve technical specifications

Part numberBrandSizeHead ØStem ØLengthGroovesMaterial
REVI-28338FS-2-6-8 SUPERTECH 29.0 mm 5.97 mm 108.9 mm 1 Inconel
REVI-28338FS-3-6-8 SUPERTECH +1 mm 30.0 mm 5.97 mm 108.9 mm 1 Inconel

Both sets share the 5.97 mm stem and the 108.9 mm length; only the head differs.

Valve fitting

PartRenault originalReinforced
Collets KPR-6S-7-16 (single groove)
Valve stem seals 7700103938
Valve guide 7700109151

These single groove valves are fitted with KPR-6S/7 collets; the original collets do not fit.

The 5.97 mm stem slides in the guides (original 7700109151): check their clearance and replace the valve stem seals (7700103938).

The exhaust seats are reground during the rebuild; with the 30 mm head they are machined to that size.

Technical guide

Our brand

SUPERTECH SUPERTECH Performance, a Californian maker, has focused for three decades and more on racing valvetrains, from valves to titanium retainers by way of guides and springs. Stainless, titanium or Inconel are selected engine by engine, then signed off by well-known builders active in rally, drift and on circuits.

How to choose

Beneath the retainer, the collets seat in the one groove cut into the stem, which keeps the valve pressed on its spring. Both versions use the same alloy and the same stem; they differ only in head diameter.

CriterionOption 1Option 2
Size 29 mm head
REVI-28338FS-2-6-8: a head at the diameter of the Renault part, for an F4Rt cylinder head whose exhaust seats do not need enlarging. The seats are simply refaced during the rebuild. It is the version to favour on a stock or lightly tuned Mégane II RS that mainly seeks the hot strength of Inconel. It must be fitted with single-groove KPR-6S-7 collets, as the original ones do not suit. The original guides are checked at the same time, since the 5.97 mm stem must slide in them without excess play.
+1 mm, 30 mm
REVI-28338FS-3-6-8: one extra millimetre of head opens a broader exit for spent gases and improves filling on the following cycle, hence more power. On a sound head, the exhaust seats are machined to 30 mm before fitting. This version suits raised boost or an advanced build, and rescues seats already reworked along the way. KPR-6S-7 collets are essential, as for the 29 mm version.

When reinforced valves become necessary

  • Boost pressure turned up on the Mégane's F4Rt
  • Sharper cam profiles or uprated valve springs
  • Regular circuit outings or hill climbs
  • Rev limit raised as part of an engine build
  • Cylinder head rebuild with marked or tired exhaust valves

Vehicle compatibility

ModelEngine codePowerYears
Mégane II (BM0/1_, CM0/1_) 2.0 Renault Sport F4Rt 774 224 hp 2004-2009
Mégane II (BM0/1_, CM0/1_) 2.0 F4R 774 230 hp 2006-2008

OEM part number (exhaust valve): 13202-00QAE

Important: a set of 8 covers the whole engine, which has two exhaust valves per cylinder; plan for KPR-6S/7 collets.

Don't forget the inlet valves

When the F4Rt head is off, take the chance to replace the stem seals too, which stop oil from creeping down the valves. The complete set for this head:

Valve stem seals F4R, set of 16 →

16 other products in the same category

Loading...