Skip to content
NSB Concept

Reinforced head gasket Lancia Fulvia Coupé 1.6 838A.100

€78.63 (tax incl.)
€104.84 (tax incl.) -25%

Cometic CFM-20 reinforced head gasket for the Lancia Fulvia Coupé 1.6. Sold individually, one gasket per engine.

  • Brand: Cometic
  • Engine: 838 A.100
  • Bores: 83 and 84 mm
  • Thicknesses: 1.09 and 1.50 mm
H2687SP1043F
0 in stock in France
On order, 15 to 30 days lead time
Pay in installments

The Lancia engines covered

The 838 A.100 petrol engine (1.6 litres, 1,584 cc), a four-cylinder, powers the Lancia Fulvia Coupé 1.6 listed below.

Nothing is published about the original gasket of this engine: no part number, no bore, no construction and no thickness. It is sized for standard combustion pressure; as soon as that pressure rises, the clamping of the head weakens, the head lifts and coolant passes into a cylinder.

Reinforced cylinder head gaskets

Sealing does not depend on the gasket alone: the bolts or studs that tighten the head onto the block count just as much. The CFM-20, with its galvanized steel core and asbestos-free soft compound, makes up for small irregularities in the gasket faces.

This page offers three part numbers from the American maker Cometic, a specialist in racing gaskets, in a single construction: CFM-20. Their bores are 83 and 84 mm and their thicknesses 1.09 and 1.50 mm. Each part number is sold individually: one gasket per engine.

Technical specifications

Gasket bore Thickness Gasket volume Gasket type
OEM not specified
Brand Part number
83 mm 1.09 mm 5.90 CFM-20 Cometic H2687043F
84 mm 1.09 mm 6.04 CFM-20 Cometic H2687SP1043F
84 mm 1.50 mm 8.31 CFM-20 Cometic H2687SP5059F

A gasket's volume is the space it leaves free above each cylinder: it adds to the combustion chamber and reduces the compression ratio. Only gaskets of the same bore can be compared.

Preparation and fitting

Fasteners Engines Tightening torque
Original cylinder head bolts 838A.100 not published by the manufacturer

Before fitting, lay a straight edge across the head and the block to check their flatness, and have whichever is warped resurfaced. Cometic checks each of its CFM-20 gaskets before shipping.

Technical guide

The construction offered

CFM-20 Cometic
A galvanized steel heart, coated on each face with a soft asbestos-free compound made of aramid fibres, mineral fillers and elastomer binders. This layered construction, between metal and fibre, combines the strength of steel with the flexibility of the compound. It is offered here in three part numbers, with a bore of 83 or 84 mm and a thickness of 1.09 or 1.50 mm.

Choosing bore and thickness

Gasket bore. The Cometic CFM-20 gasket is offered in 83 mm (H2687043F) and in 84 mm (H2687SP1043F and H2687SP5059F).

Thickness. No thickness is given for the original gasket of this engine: the dimension of the removed gasket serves as the reference. A thicker gasket enlarges the combustion chamber and lowers the compression ratio; a thinner one reduces it and raises the ratio.

Your goal Thickness to choose
Keep the original compression ratio Original thickness not published: measure the removed gasket and compare its dimension with the two thicknesses offered, 1.09 and 1.50 mm
Skimmed cylinder head, make up the lost height Two thicknesses are offered, 1.09 and 1.50 mm: compare them with that of the removed gasket, increased by the material taken off when resurfacing
Forced induction build, lower the ratio 1.09 mm, if the thickness measured on the removed gasket is closer to this value
Naturally aspirated build, raise the ratio 1.50 mm, if the thickness measured on the removed gasket is closer to this value

As no original thickness is published, measure with a dial gauge how far the pistons protrude above the block's gasket face, above all before choosing the 1.09 mm gasket: this shows the clearance left between piston and head.

The brand

Cometic Cometic Gasket, Inc. is an American company, founded in 1989 in Concord (Ohio), that makes gaskets and sealing solutions for engines. It owes its reputation to the custom-cut gasket, made to the bore and thickness requested and produced entirely in the United States from American raw materials.

Advantages over the original gasket

Criterion Original gasket, part number not published Reinforced gaskets
Construction Construction not stated by the manufacturer Galvanized steel core and asbestos-free compound (CFM-20)
Gasket bore not published by the manufacturer 83 / 84 mm
Thicknesses available thickness not published by the manufacturer 1.09 to 1.50 mm
Compression ratio adjustment None Through the thickness chosen
Resistance to overpressure Limited to standard output Designed for forced induction

When a reinforced gasket becomes necessary

  • Adding forced induction, or raising boost on an already turbocharged engine
  • Cylinder rebored beyond what the 83 and 84 mm bores of the gaskets offered covers
  • Looking for a compression ratio different from standard, higher or lower
  • Engine that has already lost its gasket, or is consuming coolant
  • Competition use, where the gasket goes through repeated temperature rises

Vehicle compatibility

Model Engine code Power Years
Lancia Fulvia Coupé 1.6 838 A.100 130 hp 1969-1970
Lancia Fulvia Coupé 1.6 838 A.100 114 hp 1970-1973

OEM part number: not published by the manufacturer.

Important: the part numbers on this page suit the Lancia 838 A.100 engine of 1.6 litres (Fulvia Coupé 1.6): check your vehicle's engine code before ordering. The gasket chosen must have a bore at least 0.5 mm larger than that of the cylinders.

Why switch to a reinforced gasket?

When the original gasket is no longer enough, this CFM-20 gasket takes over: the steel core keeps its shape under combustion pressure, and the soft compound on both faces follows the small flaws of the head and block.

On a pushed engine, the head gasket is often the first part to give way, at the top of the engine. The reinforced gasket prevents the leak, whereas the head removal that would follow costs far more than the gasket itself.

16 other products in the same category

Viewed products

Loading...