Skip to content
NSB Concept

Reinforced head gasket Jaguar XJ XJ-S AJ6 3.6

€179.76 (tax incl.)
€239.68 (tax incl.) -25%

Reinforced Cometic head gasket in copper. Sold individually, one gasket per engine.

  • Brand: Cometic
  • Engines: AJ6 3.6 L
  • Bore: 92.5 mm
  • Thickness: 1.60 mm
  • Replaces: NBC2520AB
H2954063C
0 in stock in France
For larger quantities, 5 to 15 days lead time
Pay in installments

The Jaguar engines covered

The AJ6 3.6-litre petrol engine, an inline six, powers the Jaguar XJ (XJ40, XJ81), XJ Coupé and XJSC Convertible (X27) listed below.

The original gasket of these engines carries the part number NBC2520AB, which serves the 3.6-litre of the XJ-S and of the XJ40 from engine 109270. Jaguar publishes neither its bore, nor its construction, nor its thickness. It is sized for the original combustion pressure: if it rises, the clamping load eases, the head lifts and coolant passes into a cylinder.

Reinforced cylinder head gaskets

Sealing does not depend on the gasket alone: the fasteners that clamp the head onto the block matter just as much. Copper of 99.9% purity resists corrosion, deforms without breaking and conducts heat well, with no brittleness under temperature.

This page describes the part number from the American maker Cometic, a specialist in racing gaskets, in a single construction: copper. Its bore is 92.5 mm and its thickness 1.60 mm. By convention, the gasket bore is at least 0.5 mm larger than that of the cylinders. It is sold individually: one gasket per engine.

Technical specifications

Gasket bore Thickness Gasket volume Gasket type
OEM not specified
Brand Part number
OEM NBC2520AB
92.5 mm 1.60 mm 10.75 Copper Cometic H2954063C

Gasket volume is the space the gasket leaves open above each cylinder. It adds to the combustion chamber, and the larger it is, the lower the compression ratio. Only gaskets of the same bore can be compared with one another.

Preparation and fitting

Fasteners Engines Tightening torque
Original cylinder head bolts AJ6 not published by the manufacturer

Before fitting, check with a straight edge that the head and block faces are flat, and have them resurfaced if necessary. Cometic checks the flatness of each of its copper gaskets.

Technical guide

The construction offered

Cometic copper
Sheet of pure oxygen-free copper, grade C110 (99.9% copper). The metal resists corrosion, compresses without splitting, dissipates heat well and stays supple at temperature. Cometic checks the flatness of each gasket; for the best result, it recommends fitting it with a crimped sealing ring.

Choosing bore and thickness

Gasket bore. The Cometic copper gasket is offered in 92.5 mm (H2954063C), with no other bore.

Thickness. Jaguar gives no thickness for the original gasket. A thicker gasket enlarges the combustion chamber and lowers the compression ratio; a thinner one reduces it and raises the ratio.

Your goal Thickness to choose
Keep the original compression ratio Original thickness not published: note that of the removed gasket and compare it with the only gasket offered, 1.60 mm
Skimmed cylinder head, make up the lost height A single thickness exists, 1.60 mm: compare it with that of the removed gasket, adding the material taken off when resurfacing
Forced induction build, lower the ratio 1.60 mm, when the thickness measured on the original gasket at removal is lower
Naturally aspirated build, raise the ratio 1.60 mm, when the thickness measured on the original gasket at removal is higher

With no published original thickness, use a dial gauge to measure how far the pistons stand proud of the block deck, especially if the removed gasket is thinner than 1.60 mm: it shows the clearance left between piston and head.

The brand

Cometic Cometic Gasket, Inc., founded in 1989 in Concord, Ohio, is an American maker of engine gaskets and sealing solutions. Its reputation rests on the made-to-measure gasket, cut to the bore and thickness wanted. All production stays in the United States, using American raw materials.

Advantages over the original gasket

Criterion Original gasket NBC2520AB Reinforced gaskets
Construction Construction not stated by the manufacturer Pure copper, 99.9% (grade C110)
Gasket bore not published by the manufacturer 92.5 mm
Thicknesses available thickness not published by the manufacturer 1.60 mm
Compression ratio adjustment None Through the thickness chosen
Resistance to overpressure Limited to standard output Designed for forced induction

When a reinforced gasket becomes necessary

  • Adding forced induction, or raising boost on an already turbocharged engine
  • Cylinder rebored beyond what the 92.5 mm bore of the gasket offered covers
  • Looking for a compression ratio different from standard, higher or lower
  • Engine that has already lost its gasket, or is consuming coolant
  • Competition use, where the gasket goes through repeated temperature rises

Vehicle compatibility

Model Engine code Power Years
Jaguar XJ (XJ40, XJ81) 3.6 AJ6 212 hp 1986-1989
Jaguar XJ Coupé 3.6 AJ6 228 and 212 hp 1983-1989
Jaguar XJ Coupé 3.6 AJ6 220 hp 1983-1988
Jaguar XJSC Convertible (X27) 3.6 AJ6 212 hp 1987-1991
Jaguar XJSC Convertible (X27) 3.6 AJ6 220 hp 1986-1988

OEM part number: NBC2520AB.

Important: the part number on this page suits the AJ6 engine of 3.6 litres: check the displacement and engine code of your vehicle before ordering.

Why switch to a reinforced gasket?

When the original gasket reaches its limit, this copper gasket takes over: pure copper is ductile and does not turn brittle when hot, so the seal between head and block is kept.

Turbo, supercharger or a raised compression ratio: the head gasket takes the strain first, the weak point of the top end. A reinforced gasket prevents the leak and the head removal that goes with it, a job far dearer than the gasket itself.

16 other products in the same category

Viewed products

Loading...