Skip to content
NSB Concept

Reinforced cylinder head gasket Ferrari 250 Europa 250 GT 250 LM Colombo V12 F250

€113.63 (tax incl.)
€151.50 (tax incl.) -25%

Reinforced Cometic head gasket, in CFM-20, for the Colombo V12 of the Ferrari 250 Europa, 250 GT and 250 LM.

  • Engine: F250
  • Bores: 75.5 or 75 mm
  • Thicknesses: 1.09 or 1.50 mm
C14101-043
0 in stock in France
On order, 15 to 30 days lead time
Pay in installments

The Ferrari engines covered

The Ferrari Colombo V12, identified by the code "F250", powers the Ferrari 250 Europa, 250 GT and 250 LM detailed below.

The maker of the Colombo V12 publishes neither the part number, nor the bore, nor the construction, nor the thickness of the original gasket. This gasket is sized for standard combustion pressure: when that pressure rises, the head loses clamping force, lifts and lets coolant reach a cylinder.

Reinforced cylinder head gaskets

The gasket does not guarantee the seal on its own: the fasteners that clamp the head onto the block weigh just as much. CFM-20 combines a galvanized steel core with a soft asbestos-free compound that makes up for small irregularities in the gasket faces. On these Ferraris, torquing in several passes keeps the pressure even.

This page offers the part numbers from the American maker Cometic, a specialist in racing gaskets, in a single construction: CFM-20. Their bore is 75.5 mm or 75 mm and their thickness 1.09 mm or 1.50 mm. Each part number is sold individually.

Technical specifications

Gasket bore Thickness Gasket volume Gasket type
OEM not specified
Brand Part number
75 mm 1.50 mm 6.63 CFM-20 Cometic C14109-059
75.5 mm 1.09 mm 4.88 CFM-20 Cometic C14101-043

A gasket's volume is the space it leaves free above each cylinder. That space adds to the combustion chamber and lowers the compression ratio; only gaskets of the same bore are comparable. Here, the two gaskets have close bores, 75.5 mm and 75 mm.

Preparation and fitting

Fasteners Engines Tightening torque
Original cylinder head bolts F250 not published by the manufacturer

Before fitting, run a straight edge over the head and the block to check their flatness, and have either one resurfaced if necessary. Cometic checks the flatness of each of its CFM-20 gaskets. This check holds for the Colombo V12 as for any other engine.

Technical guide

The construction offered

CFM-20 Cometic
A galvanized steel core, lined on each face with a soft asbestos-free compound blending aramid fibres, mineral fillers and elastomer binders. This layered structure, between metal and fibre, joins the stiffness of steel to the give of the compound. It is offered here as two part numbers: 75.5 mm with a 1.09 mm thickness, 75 mm with 1.50 mm.

Choosing bore and thickness

Gasket bore. The Cometic CFM-20 gasket is offered in 75.5 mm (C14101-043) and in 75 mm (C14109-059).

Thickness. For the original gasket of the Colombo V12, the manufacturer gives no thickness. A thicker gasket enlarges the combustion chamber and lowers the compression ratio; a thinner one reduces it and raises the ratio.

Your goal Thickness to choose
Keep the original compression ratio Original thickness not published: measure the removed gasket and compare its size with the two part numbers offered, 1.09 mm and 1.50 mm
Skimmed cylinder head, make up the lost height Two thicknesses exist, 1.09 mm and 1.50 mm: take the one nearest to that of the removed gasket, plus the material taken off in resurfacing
Forced induction build, lower the ratio 1.09 mm, if the thickness measured on the original gasket at removal is lower
Naturally aspirated build, raise the ratio 1.50 mm, if the thickness measured on the original gasket at removal is higher

With no published original thickness, use a dial gauge to measure how far the pistons stand proud of the block's gasket face, above all if the removed gasket is thinner than 1.09 mm: this reading gives the clearance left between piston and head.

The brand

Cometic Cometic Gasket, Inc. is an American manufacturer of gaskets and sealing solutions for engines, founded in 1989 in Concord, Ohio. Its reputation rests on the made-to-measure gasket, cut to the bore and thickness requested; all production takes place in the United States, from American raw materials. The part numbers C14101-043 and C14109-059 are its own.

Advantages over the original gasket

Criterion Original gasket, part number not published Reinforced gaskets
Construction Construction not stated by the manufacturer Galvanized steel core and asbestos-free compound (CFM-20)
Gasket bore not published by the manufacturer 75,5 / 75 mm
Thicknesses available thickness not published by the manufacturer 1.09 to 1.50 mm
Compression ratio adjustment None Through the thickness chosen
Resistance to overpressure Limited to standard output Designed for forced induction

When a reinforced gasket becomes necessary

  • Adding forced induction, or raising boost on an already turbocharged engine
  • Cylinder rebored beyond what the 75.5 mm or 75 mm bore of the gasket offered covers
  • Looking for a compression ratio different from standard, higher or lower
  • Engine that has already lost its gasket, or is consuming coolant
  • Competition use, where the gasket goes through repeated temperature rises

Vehicle compatibility

Model Engine code Power Years
Ferrari 250 Europa F250 not published 1954-1955
Ferrari 250 GT F250 not published 1954-1959
Ferrari 250 LM F250 not published 1963

OEM part number: not published by the manufacturer.

Important: the part numbers on this page suit the manufacturer's Ferrari 250 Europa, 250 GT and 250 LM: the cylinder bank is not specified, and a V12 has two, so check before ordering, along with your engine's bore, 75.5 mm for C14101-043 and 75 mm for C14109-059.

Why switch to a reinforced gasket?

When the original gasket reaches its limits, this CFM-20 gasket takes over: the steel core keeps its shape under combustion pressure, while the soft compound on both faces follows the small flaws of the head and block. The Colombo V12 finds here two gaskets, one at 75.5 mm, the other at 75 mm.

On an engine driven to its limit, the head gasket is the first part to fail, the weak point of the top end. A reinforced gasket prevents the leak, whereas the head removal that follows, a long and delicate job, costs much more than the gasket. This holds for the Colombo V12 as for any hard-driven engine.

16 other products in the same category

Viewed products

Loading...