Reinforced cylinder head gasket Ford V6 2.8 PR5 PR6 PR7
Reinforced Cometic CFM-20 head gasket, one gasket per cylinder bank (left and right).
- Brand: Cometic
- Engines: PR5, PR6, PR7, PR8, PRB, PRC, PRD, PRG, PRN, PRT, PYA, PYN, PYU
- Bores: 92 and 95 mm
- Thicknesses: 1.09 and 1.5 mm
- Replaces: 6 140 740
The Ford engines covered
The Ford Cologne V6 of 2.8 litres, identified by the codes PR5, PR6, PR7, PR8, PRB, PRC, PRD, PRG, PRN, PRT, PYA, PYN and PYU, powers the Capri III, Granada II, Sierra I and Sierra II listed below.
The original gasket of these engines carries the part number 6 140 740. Ford publishes neither its bore, nor its thickness, nor its construction. It is sized for the original combustion pressure: if it rises, the clamping load eases, the head lifts and coolant passes into a cylinder.
Reinforced cylinder head gaskets
Sealing does not rest on the gasket alone: the fasteners that clamp the head to the block count just as much. The CFM-20 combines a galvanized steel core with an asbestos-free compound applied to both faces.
This page describes the part numbers from the American maker Cometic, a specialist in racing gaskets, in a single construction: CFM-20. The bores are 92 and 95 mm and the thicknesses 1.09 and 1.5 mm. Each part number comes in a left-hand and a right-hand version, one per cylinder bank. By convention, the gasket bore is at least 0.5 mm larger than that of the cylinders. They are sold individually: one gasket per cylinder bank.
Technical specifications
| Gasket bore | Thickness | Gasket volume | Gasket type OEM not specified |
Brand | Part number OEM 6 140 740 |
| 92 mm | 1.50 mm | 9.97 | CFM-20 left bank |
Cometic | H2423SP1059F |
| 92 mm | 1.50 mm | 9.97 | CFM-20 right bank |
Cometic | H2423SP2059F |
| 95 mm | 1.09 mm | 7.73 | CFM-20 left bank |
Cometic | H2423SP3043F |
| 95 mm | 1.09 mm | 7.73 | CFM-20 right bank |
Cometic | H2423SP4043F |
The volume of a gasket corresponds to the hollow it leaves above each cylinder. That hollow adds to the combustion chamber: the wider it is, the lower the compression ratio falls. Compare only gaskets of the same bore, otherwise the comparison means nothing.
Preparation and fitting
| Fasteners | Engines | Tightening torque |
| Original cylinder head bolts | PR5, PR6, PR7, PR8, PRB, PRC, PRD, PRG, PRN, PRT, PYA, PYN, PYU | not published by the manufacturer |
Before fitting the gasket, run a straightedge across the head and block faces to check they are flat, and have them resurfaced if needed. An uneven face lets coolant or pressure escape, even with a reinforced gasket.
Technical guide
The construction offered
| CFM-20 Cometic A galvanized steel core covered on both faces with a soft asbestos-free compound made of aramid fibres, mineral fillers and elastomer binders. This laminated construction, part metal and part fibre, combines the strength of steel with the softness of the compound. It is offered here in two bores and two thicknesses, with one gasket for each cylinder bank. |
Choosing bore and thickness
Gasket bore. The Cometic CFM-20 comes in 92 and 95 mm, each in a left-hand and a right-hand version.
Thickness. Ford gives no thickness for the original gasket. A thicker gasket enlarges the combustion chamber and lowers the compression ratio; a thinner one reduces it and raises the ratio.
| Your goal | Thickness to choose |
| Keep the original compression ratio | Original thickness not published by the manufacturer: note that of the removed gasket and compare it with the two thicknesses offered, 1.09 and 1.5 mm |
| Skimmed cylinder head, make up the lost height | Two thicknesses exist, 1.09 and 1.5 mm: start from that of the removed gasket, plus the metal taken off when resurfacing |
| Forced induction build, lower the ratio | 1.5 mm, if the removed gasket is thinner |
| Naturally aspirated build, raise the ratio | 1.09 mm, if the removed gasket is thicker |
With no published original thickness, use a dial gauge to measure how far the pistons stand proud of the block deck, especially if the removed gasket is thinner than 1.09 mm: it shows the clearance left between piston and head.
The brand
| Cometic Gasket, Inc. is an American maker of engine gaskets and sealing solutions, set up in 1989 in Concord, Ohio. Its speciality is the made-to-measure gasket, cut to the bore and thickness requested. All manufacturing stays in the United States, from American raw materials. |
Advantages over the original gasket
| Criterion | Original gasket 6 140 740 | Reinforced gaskets |
| Construction | Construction not stated by the manufacturer | Galvanized steel core, asbestos-free compound on both faces |
| Gasket bore | not published by the manufacturer | 92 and 95 mm |
| Thicknesses available | thickness not published by the manufacturer | 1.09 to 1.5 mm, 2 values |
| Compression ratio adjustment | None | Through the thickness chosen |
| Resistance to overpressure | Limited to standard output | Designed for forced induction |
When a reinforced gasket becomes necessary
- Adding forced induction, or raising boost on an already turbocharged engine
- Cylinder rebored beyond what the 92 or 95 mm bore of the gasket offered covers
- Looking for a compression ratio different from standard, higher or lower
- Engine that has already lost its gasket, or is consuming coolant
- Competition use, where the gasket goes through repeated temperature rises
Vehicle compatibility
| Brand | Model | Engine code | Power | Years |
| Ford | CAPRI III (GECP) 2.8 Super Injection | PRN | 160 hp | 1981-1987 |
| Ford | CAPRI III (GECP) 2.8 i Turbo | PYN | 188 hp | 1982-1987 |
| Ford | GRANADA II (GU) 2.8 i | PRB | 160 hp | 1977-1981 |
| Ford | GRANADA II (GU) 2.8 i | PRC | 150 hp | 1982-1985 |
| Ford | GRANADA II (GU) 2.8 i | PRD | 147 hp | 1977-1985 |
| Ford | GRANADA II (GU) 2.8 | PYA | 135 hp | 1977-1985 |
| Ford | GRANADA II (GU) 2.8 | PYU | 132 hp | 1981-1985 |
| Ford | GRANADA Turnier (GNU) 2.8 i | PRB | 160 hp | 1977-1981 |
| Ford | GRANADA Turnier (GNU) 2.8 i | PRC | 150 hp | 1982-1985 |
| Ford | GRANADA Turnier (GNU) 2.8 i | PRD | 147 hp | 1977-1985 |
| Ford | GRANADA Turnier (GNU) 2.8 | PYA | 135 hp | 1977-1985 |
| Ford | GRANADA Turnier (GNU) 2.8 | PYU | 132 hp | 1981-1985 |
| Ford | SIERRA I Berline à hayon (GBC) 2.8 XR 4x4 | PRT | 150 hp | 1985-1986 |
| Ford | SIERRA I Berline à hayon (GBC) 2.8 XR4i | PR5 | 146 hp | 1982-1986 |
| Ford | SIERRA I Berline à hayon (GBC) 2.8 XR4i | PR6 | 143 hp | 1982-1986 |
| Ford | SIERRA I Berline à hayon (GBC) 2.8 XR4i | PRT | 150 hp | 1982-1986 |
| Ford | SIERRA I Berline à hayon (GBC) 2.8 i XR 4x4 | PR5 | 146 hp | 1983-1986 |
| Ford | SIERRA I Berline à hayon (GBC) 2.8 i XR 4x4 | PR6 | 146 hp | 1983-1986 |
| Ford | SIERRA II (GBG, GB4) 2.8 i | PR8 | 143 hp | 1987-1993 |
| Ford | SIERRA II Berline à hayon (GBC, GBG) 2.8 i XR 4x4 | PR7 | 146 hp | 1987-1993 |
| Ford | SIERRA II Berline à hayon (GBC, GBG) 2.8 i XR 4x4 | PRG | 150 hp | 1987-1988 |
| Ford | SIERRA II Berline à hayon (GBC, GBG) 2.8 i | PR8 | 143 hp | 1987-1993 |
| Ford | SIERRA II Berline à hayon (GBC, GBG) 2.8 | PRG | 150 hp | 1987-1989 |
| Ford | SIERRA II Turnier (BNG) 2.8 4x4 | PRG | 150 hp | 1987-1988 |
| Ford | SIERRA II Turnier (BNG) 2.8 i 4x4 | PR7 | 146 hp | 1987-1993 |
| Ford | SIERRA II Turnier (BNG) 2.8 i | PR7 | 146 hp | 1987-1993 |
| Ford | SIERRA II Turnier (BNG) 2.8 i | PR8 | 143 hp | 1987-1993 |
| Ford | SIERRA Turnier (BNC) 2.8 XR4i | PR5 | 146 hp | 1982-1986 |
| Ford | SIERRA Turnier (BNC) 2.8 XR4i | PR6 | 143 hp | 1982-1986 |
| Ford | SIERRA Turnier (BNC) 2.8 i 4x4 | PR6 | 143 and 146 hp | 1982-1986 |
OEM part number: 6 140 740.
Important: the gaskets on this page are listed for the Ford V6 engines of 2.8 litres in the table (1977 to 1993). For any other vehicle, note the engine code before ordering.
Why switch to a reinforced gasket?
When the original gasket reaches its limits, this CFM-20 gasket takes over: its galvanized steel core holds its shape, while the asbestos-free compound seals the joint between head and block.
Adding a turbo or a supercharger, or raising the compression ratio, puts the head gasket under heavy strain: it is the weak link of the top end. A reinforced gasket rules out the leak and the head removal it forces, an operation far dearer than the part.
-
Brand
-
ReferenceH2423SP1059F