Skip to content
  • On order
Reinforced head gasket Mercedes M120 V12 - C4500-027 Reinforced head gasket Mercedes M120 V12 - C4500-027

Reinforced cylinder head gasket Mercedes-Benz M120 V12 6.0L

€406.20 (tax incl.)
€541.60 (tax incl.) -25%

Reinforced Cometic head gasket in multilayer MLS for the Mercedes-Benz 6.0-litre V12 engine, one part number per cylinder bank.

  • Engines: M120.980 M120.981 M120.982 M120.983 M297
  • Bore: 90 mm
  • Thicknesses: 0.69 to 3.56 mm
C4500-027
0 in stock in France
ORDER TODAY, WE SHIP IN 3 WEEKS
Pay in installments

The Mercedes-Benz engines covered

Mercedes-Benz's 6.0-litre twelve-cylinder V engine, known as the M120 and offered as the M120.980, M120.981, M120.982 and M120.983, powers the S-Class (W140) 600 SE and 600 SEL, the SEC and CL 600 coupés (C140) and the SL 600 (R129) in the table below. The engine has two heads: one gasket is needed per cylinder bank, so two per engine, a right-hand and a left-hand.

The manufacturer part number of the standard gasket is 120 016 20 20; neither the bore, nor the thickness, nor the construction appears in any manufacturer documentation. The standard gasket is sized for the original combustion pressure: beyond it, the clamping load fades, the head lifts and coolant passes into a cylinder.

Reinforced cylinder head gaskets

The gasket alone does not provide the seal: the fasteners that clamp the head to the block count as much as it does. Beyond 100 N/mm², a composite gasket settles for good; the 301 stainless steel of the MLS carries 517 N/mm², 5 times more, and springs back to shape with every combustion. The raised features of the outer plates pass on the clamping load around each cylinder and each fluid passage, without any machining of the block.

This page gathers the part numbers of a single racing manufacturer, Cometic, in multi-layer MLS construction, with a 90 mm gasket bore in two versions, one per cylinder bank. Thicknesses run from 0.686 to 3.556 mm, enough to adjust the compression ratio without altering either the pistons or the heads. As a rule, the gasket bore chosen is at least 0.5 mm larger than the actual cylinder bore. Each part number is sold individually and for one cylinder bank only: one is needed on the right and one on the left.

Technical specifications

Gasket bore Thickness Gasket volume Gasket type
OEM not specified
Brand Part number
OEM 120 016 20 20
90 mm 0.69 mm 4.39 MLS
right bank
Cometic C4500-027
90 mm 0.69 mm 4.39 MLS
left bank
Cometic C4501-027
90 mm 0.76 mm 4.83 MLS
right bank
Cometic C4500-030
90 mm 0.76 mm 4.83 MLS
left bank
Cometic C4501-030
90 mm 0.91 mm 5.79 MLS
right bank
Cometic C4500-036
90 mm 0.91 mm 5.79 MLS
left bank
Cometic C4501-036
90 mm 1.02 mm 6.49 MLS
right bank
Cometic C4500-040
90 mm 1.02 mm 6.49 MLS
left bank
Cometic C4501-040
90 mm 1.14 mm 7.25 MLS
right bank
Cometic C4500-045
90 mm 1.14 mm 7.25 MLS
left bank
Cometic C4501-045
90 mm 1.30 mm 8.27 MLS
right bank
Cometic C4500-051
90 mm 1.30 mm 8.27 MLS
left bank
Cometic C4501-051
90 mm 1.42 mm 9.03 MLS
right bank
Cometic C4500-056
90 mm 1.42 mm 9.03 MLS
left bank
Cometic C4501-056
90 mm 1.52 mm 9.67 MLS
right bank
Cometic C4500-060
90 mm 1.52 mm 9.67 MLS
left bank
Cometic C4501-060
90 mm 1.68 mm 10.69 MLS
right bank
Cometic C4500-066
90 mm 1.68 mm 10.69 MLS
left bank
Cometic C4501-066
90 mm 1.78 mm 11.32 MLS
right bank
Cometic C4500-070
90 mm 1.78 mm 11.32 MLS
left bank
Cometic C4501-070
90 mm 1.91 mm 12.15 MLS
right bank
Cometic C4500-075
90 mm 1.91 mm 12.15 MLS
left bank
Cometic C4501-075
90 mm 2.03 mm 12.91 MLS
right bank
Cometic C4500-080
90 mm 2.03 mm 12.91 MLS
left bank
Cometic C4501-080
90 mm 2.13 mm 13.55 MLS
right bank
Cometic C4500-084
90 mm 2.13 mm 13.55 MLS
left bank
Cometic C4501-084
90 mm 2.18 mm 13.87 MLS
right bank
Cometic C4500-086
90 mm 2.18 mm 13.87 MLS
left bank
Cometic C4501-086
90 mm 2.34 mm 14.89 MLS
right bank
Cometic C4500-092
90 mm 2.34 mm 14.89 MLS
left bank
Cometic C4501-092
90 mm 2.49 mm 15.84 MLS
right bank
Cometic C4500-098
90 mm 2.49 mm 15.84 MLS
left bank
Cometic C4501-098
90 mm 3.05 mm 19.40 MLS
right bank
Cometic C4500-120
90 mm 3.05 mm 19.40 MLS
left bank
Cometic C4501-120
90 mm 3.56 mm 22.65 MLS
right bank
Cometic C4500-140
90 mm 3.56 mm 22.65 MLS
left bank
Cometic C4501-140

Gasket volume is the space left free above each cylinder. It adds to the combustion chamber and lowers the compression ratio by the same amount. Restrict the comparison to gaskets of the same bore.

Preparation and fitting

Fasteners Engines Tightening torque
Original cylinder head bolts M120.980, M120.981, M120.982, M120.983, M297 not published by the manufacturer

Before refitting, run a straight edge over the head and the block to check their flatness, and have the surface that needs it resurfaced. Add no sealing paste: Cometic gaskets are supplied already coated.

Technical guide

The construction offered

Cometic MLS cylinder head gasket Cometic MLS
Stamped stainless steel plates, stacked on one another and riveted. The outer plates show active beads around each cylinder and each liquid passage. The gasket seals with a moderate clamping load and barely distorts the bore. It is the do-it-all solution, from the tuned naturally aspirated engine to sensible boost.

Choosing bore and thickness

Gasket bore. The Cometic MLS comes in 90 mm for the right bank (C4500) and for the left bank (C4501). The part numbers cover the M120 of 6.0 litres and the M297 of 6.9 and 7.0 litres.

Thickness. No figure is supplied by the manufacturer for the standard gasket: only the reading of the gasket you remove counts. A thicker gasket enlarges the combustion chamber and lowers the compression ratio; a thinner one reduces it and raises the ratio.

Your goal Thickness to choose
Keep the original compression ratio Standard thickness not on record: measure the gasket you remove, then use the closest figure between 0.686 and 3.556 mm
Skimmed cylinder head, make up the lost height From 0.686 to 3.556 mm, use the thickness of the removed gasket plus the material the resurfacing took off
Forced induction build, lower the ratio 3.556 mm, if the removed gasket is thinner
Naturally aspirated build, raise the ratio 0.686 mm, if the removed gasket is thicker

When no original thickness is published, use a dial gauge to measure how far the pistons protrude above the block deck: that gives the clearance remaining between piston and head, particularly with the thinnest gasket.

The brand

Cometic Cometic Gasket, Inc., a company from the United States founded in 1989 in Concord, Ohio, designs engine gaskets and sealing solutions. It has made a speciality of the custom gasket, at the bore and thickness requested, built entirely in the United States from American materials.

Advantages over the original gasket

Criterion Original gasket 120 016 20 20 Reinforced gaskets
Construction Not specified by the manufacturer Multi-layer stainless steel, or steel and aramid fibre with a stainless ring
Gasket bore not published by the manufacturer 90 mm
Thicknesses available not published by the manufacturer 0.686 to 3.556 mm, 18 values
Compression ratio adjustment None Through the thickness chosen
Resistance to overpressure Limited to standard output Designed for forced induction

When a reinforced gasket becomes necessary

  • Adding forced induction, or raising boost on an already turbocharged engine
  • Cylinder rebored beyond what the bore of the gaskets offered (90 mm) covers
  • Looking for a compression ratio different from standard, higher or lower
  • Engine that has already lost its gasket, or is consuming coolant
  • Competition use, where the gasket goes through repeated temperature rises

Vehicle compatibility

Brand Model Engine code Power Years
Mercedes-Benz CLASSE S (W140) 600 SE, SEL, S 600 (140.056, 140.057) M120.980, M120.982 394 and 408 hp 04.1991 - 10.1998
Mercedes-Benz CLASSE S Coupé (C140) SEC, CL 600 (140.076) M120.980, M120.982 367, 394 and 408 hp 07.1992 - 02.1999
Mercedes-Benz SL (R129) 600, 600 SL (129.076) M120.981, M120.983 394 and 408 hp 02.1992 - 10.2001

OEM part number: 120 016 20 20.

Important: the gaskets on this page are listed for the M120.980, M120.981, M120.982 and M120.983 engines in the survey below and, according to the manufacturer, for the M297 too. For any other vehicle, find the engine code first before placing an order.

Why switch to a reinforced gasket?

When the standard gasket is no longer enough, the reinforced one takes over: at higher combustion pressure it holds its geometry rather than sagging.

Ask an engine for still more, with extra boost, a higher compression ratio or a thorough build, and the head gasket is the first part in the top end to give up. A reinforced gasket spares you the leak and the cylinder head removal that goes with it, a job that costs far more than the part itself.

16 other products in the same category

Viewed products

Loading...