Skip to content
  • On order
Reinforced head gasket Fiat Punto S1600 - 338409R Reinforced head gasket Fiat Punto S1600 - 338409R

Reinforced head gasket Fiat Punto S1600

€134.68 (tax incl.)
€179.58 (tax incl.) -25%

Reinforced Athena MLS head gasket. Sold individually, one gasket per engine.

  • Brand: Athena
  • Engine: S1600
  • Bore: 84 mm
  • Thickness: 1.55 mm
338409R
0 in stock in France
ORDER TODAY, WE SHIP IN 3 WEEKS
Pay in installments

The Fiat engines covered

The S1600 engine is the naturally aspirated 1.6 litre four-cylinder of the Fiat Punto Super 1600 rally car, a class created by the FIA in 2000 and capped at 1,640 cc.

No manufacturer data is published for the original gasket: neither its part number, nor its bore, nor its construction, nor its thickness. It is sized for the standard combustion pressure; as soon as that rises, the clamping load fades, the head lifts and coolant seeps into a cylinder. For the S1600 engine, none of these values is released.

Reinforced cylinder head gaskets

Sealing is not down to the gasket alone: the fasteners that clamp the head onto the block contribute just as much. A composite gasket gives up for good beyond 100 N/mm², whereas the 301 stainless steel of an MLS gasket holds 517 N/mm² and regains its shape after every combustion. Replace the bolts or studs as the workshop preparing the engine recommends.

This page presents the part number from Athena, an Italian maker of racing gaskets, in one construction only: the MLS, a multilayer stainless steel gasket. Its bore is 84 mm and its thickness 1.55 mm. As a rule, the gasket bore must exceed that of the cylinders by at least 0.5 mm. It is sold individually: a single gasket fits one engine.

Technical specifications

Gasket bore Thickness Gasket volume Gasket type
OEM not specified
Brand Part number
84 mm 1.55 mm 8.59 MLS Athena 338409R

A gasket's volume is the space it leaves free above each cylinder. That space joins the combustion chamber and lowers the compression ratio; only gaskets of the same bore can be compared. Here, the bore offered is 84 mm.

Preparation and fitting

Fasteners Engines Tightening torque
Original cylinder head bolts S1600 not published by the manufacturer

Before fitting, check the flatness of the head and block with a straight edge and have them resurfaced if needed. Athena supplies this gasket ready to fit: apply no sealing paste. On a rally engine, this check is repeated at every rebuild.

Technical guide

The construction offered

Athena MLS cylinder head gasket Athena MLS
Several layers of AISI 301 stainless steel, laser cut, stamped and then riveted together. Around each cylinder, a layer folded over on itself, the Gas Stopper, concentrates the clamping load on the combustion chamber, while beads block the water and oil passages. The outer layers carry a two-coat finish: the first withstands high temperatures and fills small irregularities of the block and head, the second, silicone based, keeps the gasket from sticking at removal. It is Athena's all-steel answer, from the tuned naturally aspirated engine to moderate forced induction. Here, the MLS is offered in 84 mm and 1.55 mm.

Choosing bore and thickness

Gasket bore. The Athena MLS exists in 84 mm (338409R), with no other bore.

Thickness. The manufacturer supplies no thickness for the original gasket. For the S1600, no value is released. A thicker gasket enlarges the combustion chamber and lowers the compression ratio; a thinner one reduces it and raises the ratio.

Your goal Thickness to choose
Keep the original compression ratio Original thickness not published: measure that of the removed gasket and set it against the only gasket available, 1.55 mm
Skimmed cylinder head, make up the lost height Only one thickness exists, 1.55 mm: set it against that of the removed gasket, plus the material taken off in resurfacing
Forced induction build, lower the ratio 1.55 mm, when the thickness measured on the original gasket at removal is lower
Naturally aspirated build, raise the ratio 1.55 mm, when the thickness measured on the original gasket at removal is higher

With no known original thickness, use a dial gauge to read how far the pistons rise above the block face, especially if the removed gasket is thicker than 1.55 mm: that figure gives the clearance left between piston and head. On this rally engine, the measurement is made with a dial gauge, head removed.

The brand

Athena Athena S.p.A. is an Italian maker of gaskets and engine components, established in Alonte, in Veneto, where its head office and main plant stand. It also has sites in Spain, the United States, Brazil and India. Several carmakers fit its multilayer gaskets on the assembly line, and its entire racing range is designed and built in Italy. Part number 338409R is the one on this page.

Advantages over the original gasket

Criterion Original gasket, part number not published Reinforced gaskets
Construction Construction not stated by the manufacturer Multilayer stainless steel (MLS)
Gasket bore not published by the manufacturer 84 mm
Thicknesses available thickness not published by the manufacturer 1.55 mm
Compression ratio adjustment None By gasket thickness (1.55 mm)
Resistance to overpressure Limited to standard output Designed for forced induction

When a reinforced gasket becomes necessary

  • Adding forced induction, or raising boost on an already turbocharged engine
  • Cylinder rebored beyond what the 84 mm bore of the gasket offered covers
  • Looking for a compression ratio different from standard, higher or lower
  • Engine that has already lost its gasket, or is consuming coolant
  • Competition use, where the gasket goes through repeated temperature rises

Vehicle compatibility

Model Engine code Power Years
Fiat Punto S1600 (Super 1600 rally car) S1600 not published -

OEM part number: not published by the manufacturer.

Important: the part number on this page suits the S1600 engine of the Fiat Punto rally car: check that your engine is an S1600 before ordering.

Why switch to a reinforced gasket?

When the original gasket is no longer enough, the reinforced gasket takes over: under higher combustion pressure it keeps its shape instead of being crushed. The S1600 finds here a gasket with an 84 mm bore.

Turbo, supercharger or a raised compression ratio: the head gasket is the first part stressed, the weak point of the top end. A reinforced gasket prevents the leak, and the head removal that goes with it costs well above the gasket. This holds for a Super 1600 rally engine too.

16 other products in the same category

Viewed products

Loading...