Skip to content
  • On order
Reinforced head gasket Renault 1.4 847 C2J - 338249R Reinforced head gasket Renault 1.4 847 C2J - 338249R

Reinforced cylinder head gasket Renault 5 Super 5 9 11 18 19 21 1.4 847 C2J

€134.68 (tax incl.)
€179.58 (tax incl.) -25%

Reinforced Athena head gasket, in O-Ring or multilayer MLS, for Renault 1.4 litre engines 847 and C2J.

  • Engines: 847, C2J
  • Bores: 77 to 78 mm
  • Thickness: 1.8 mm
  • Replaces: 77 00 680 689, 77 00 705 406, 77 01 349 331
338249R
0 in stock in France
ORDER TODAY, WE SHIP IN 3 WEEKS
Pay in installments

The Renault engines covered

The 1.4 litre petrol engines on this page, with the codes 847 and C2J, power the Renault 5, Super 5, 9, 11, 18, 19, 21, Fuego, Rapid and Trafic in the table, from 1978 to 1994. With a single cylinder head, the gasket is sold individually: one is needed per engine.

The original gasket carries the part numbers 77 00 680 689, 77 00 705 406 and 77 01 349 331 according to the TecDoc parts database. The manufacturer publishes neither its bore, nor its thickness, nor its construction. It is sized for standard combustion pressure: when that rises, the clamping load drops, the head lifts and coolant reaches a cylinder.

Reinforced cylinder head gaskets

The seal does not rest on the gasket alone: it also depends on the fasteners that clamp the head onto the block. A composite gasket crushes for good beyond 100 N/mm², whereas the 301 stainless steel of the MLS withstands 517 N/mm², 5 times more, and springs back with every combustion. With the O-Ring, the stainless ring isolates the combustion chamber on its own, and the gasket body closes the water and oil circuits. On these engines, new bolts at every refit limit head movement and leaks.

This page brings together the part numbers of the racing manufacturer Athena, in two constructions: the stainless-ring O-Ring and the multilayer MLS. Gasket bores run from 77 to 78 mm, with a single thickness of 1.8 mm. As a rule, the gasket bore chosen is at least 0.5 mm larger than the actual cylinder bore. Each part number is sold individually, one gasket per engine.

Technical specifications

Gasket bore Thickness Gasket volume Gasket type
OEM not specified
Brand Part number
OEM 77 00 680 689 | 77 00 705 406 | 77 01 349 331
77 mm 1.80 mm 8.38 MLS Athena 338249R
77 mm 1.80 mm 8.38 O-Ring Athena 330005R
77.5 mm 1.80 mm 8.49 O-Ring Athena 330009R
78 mm 1.80 mm 8.60 MLS Athena 338250R

The volume of a gasket is the space it leaves open above each cylinder. It adds to the combustion chamber: the larger it is, the lower the compression ratio. Compare these volumes only between gaskets of the same bore. Here, the bores offered run from 77 to 78 mm.

Preparation and fitting

Fasteners Engines Tightening torque
Original cylinder head bolts 847, C2J not published by the manufacturer

Before fitting the gasket, check with a straightedge that the cylinder head and block are flat, and have them resurfaced if needed. There is no need to add sealant: Athena supplies its gaskets already coated. This check applies to all four part numbers on this page.

Technical guide

The two constructions offered

Athena O-Ring cylinder head gasket O-Ring / Cut Ring Athena
A steel core covered with asbestos-free aramid fibre, with a stainless compression ring crimped around each cylinder. The ring concentrates the clamping load on a narrow band, exactly where the seal is decided, while a silicone bead protects the water and oil passages. It is the construction that best withstands high combustion pressures, intended for the most heavily stressed engines. On this page, these are part numbers 330005R, in 77 mm, and 330009R, in 77.5 mm.
Athena MLS cylinder head gasket Athena MLS
Two to five AISI 301 stainless steel sheets, laser-cut, embossed and then riveted. One of them is folded around each cylinder into a Gas Stopper that directs the clamping load towards the combustion chamber, while embossed ridges close the water and oil circuits. The outer faces are coated: one layer withstands heat and fills small flaws in the block and head, a silicone layer stops the gasket sticking when it is removed. It is Athena's all-steel solution, the one chosen for the tuned naturally aspirated engine as well as for moderate boost. On this page, these are part numbers 338249R, in 77 mm, and 338250R, in 78 mm.

Choosing bore and thickness

Gasket bore. The Athena O-Ring comes in 77 mm (330005R) and 77.5 mm (330009R), the Athena MLS in 77 mm (338249R) and 78 mm (338250R).

Thickness. The manufacturer publishes no thickness for the original gasket of these Renault engines. A thicker gasket enlarges the combustion chamber and lowers the compression ratio; a thinner one reduces it and raises the ratio.

Your goal Thickness to choose
Keep the original compression ratio Original thickness not published: measure the removed gasket and compare it with the one thickness offered, 1.8 mm
Skimmed cylinder head, make up the lost height Only one thickness is offered, 1.8 mm: compare it with that of the removed gasket, plus the metal taken off when resurfacing
Forced induction build, lower the ratio 1.8 mm, if the removed gasket is thinner
Naturally aspirated build, raise the ratio 1.8 mm, if the removed gasket is thicker

Since the original thickness is not published, measure with a dial gauge how far the pistons stand above the block deck: the figure shows the clearance left between piston and head with the 1.8 mm thickness.

The brand

Athena Athena S.p.A. is an Italian company that designs gaskets and engine parts in Alonte, in the Veneto, where its head office and main factory are located. It also has sites in Spain, the United States, Brazil and India. Its multilayer gaskets are fitted as original equipment by car makers, and its entire competition range is designed and built in Italy. Part numbers 330009R, 338249R and 338250R are the ones on this page.

Advantages over the original gasket

Criterion Original gasket 77 00 680 689, 77 00 705 406 and 77 01 349 331 Reinforced gaskets
Construction Not specified by the manufacturer Multi-layer stainless steel, or steel and aramid fibre with a stainless ring
Gasket bore not published by the manufacturer 77 to 78 mm
Thicknesses available not published by the manufacturer 1.8 mm, 1 value
Compression ratio adjustment None Through the thickness chosen
Resistance to overpressure Limited to standard output Designed for forced induction

When a reinforced gasket becomes necessary

  • Adding forced induction, or raising boost on an already turbocharged engine
  • Cylinder rebored beyond what the bore of the gaskets offered (77 to 78 mm) covers
  • Looking for a compression ratio different from standard, higher or lower
  • Engine that has already lost its gasket, or is consuming coolant
  • Competition use, where the gasket goes through repeated temperature rises

Vehicle compatibility

Brand Model Engine code Power Years
Renault 5 (122_) 847 59 and 63 hp 1982-1985
Renault 5 (122_) C2J 63 hp 1982-1985
Renault Super 5 (B/C40_) C2J 60, 67 and 71 hp 1984-1990
Renault 9 (L42_) C2J 58, 60, 67, 68 and 72 hp 1981-1988
Renault 11 (B/C37_) C2J 58, 60, 67, 68 and 72 hp 1983-1988
Renault 18 (134_) 847 64 and 77 hp 1978-1991
Renault 18 Variable (135_) 847 64 and 77 hp 1979-1991
Renault 19 I Chamade (L53_) C2J 58 hp 1988-1992
Renault Rapid Fourgon/monospace (F40_, G40_) C2J 60 hp 1986-1991
Renault Fuego (136_) 847 64 hp 1980-1985
Renault 19 I (B/C53_) C2J 58 hp 1989-1993
Renault Trafic Autobus/Autocar (T_, P_, V_) 847 48 hp 1980-1989
Renault Trafic Fourgon (T_, P_, V_) 847 48 hp 1980-1989
Renault 11 Fourgon/berline à hayon (S37_) C2J 60 and 68 hp 1983-1986
Renault 18 Fourgon/Break 847 64 hp 1979-1986
Renault 21 Berline tricorps (L48_) C2J 69 hp 1988-1993
Renault Trafic Camion plate-forme/Châssis (T_, P_, V_) 847 48 hp 1980-1989
Renault 21 (B48_) C2J 69 hp 1989-1993
Renault 19 II Chamade (L53_) C2J 60 hp 1992-1994

OEM part number: 77 00 680 689, 77 00 705 406, 77 01 349 331.

Important: the gaskets on this page are listed for the Renault models in the table, from 1978 to 1994. For any other vehicle, note the engine code before ordering.

Why switch to a reinforced gasket?

Once the original gasket reaches its limits, the reinforced one takes over: under higher combustion pressure it keeps its shape and does not crush. The Renault 847 and C2J engines get four part numbers here.

As soon as boost or the compression ratio goes up, the head gasket is the first part to give way in a built engine. A reinforced gasket prevents the leak, and the cylinder head removal that would follow: a job out of all proportion to the price of the part. This holds for the Renault models in the table as for any hard-driven engine.

16 other products in the same category

Viewed products

Loading...