- On order
Reinforced cylinder head gasket Chevrolet Cavalier and Pontiac Grand Am LD9
Reinforced Cometic MLS cylinder head gasket for the LD9 Quad 4 engine of Buick, Chevrolet, Oldsmobile and Pontiac models. Sold individually.
- Engine: LD9
- Bore: 91.31 mm
- Thickness: 1.30 mm
The Chevrolet engines covered
The LD9 Quad 4 petrol engine powers several Buick, Chevrolet, Oldsmobile and Pontiac models, detailed below.
No manufacturer data is published on the original gasket: neither its part number, nor its bore, nor its construction, nor its thickness. Sized for the standard combustion pressure, it is no longer enough once that pressure rises: the clamping load fades, the head lifts slightly and coolant reaches a cylinder.
Reinforced cylinder head gaskets
Sealing does not depend on the gasket alone: the fasteners that clamp the head to the block contribute just as much. The stainless steel of an MLS gasket holds its load under high pressure, where a conventional gasket gives way.
This page presents the two part numbers of the American maker Cometic, a specialist in racing gaskets, in a single construction: MLS, a three-layer stainless steel multilayer. Their bore is 91.31 mm and their thickness 1.30 mm. The first is intended for engines with exhaust gas recirculation (EGR), the second for those without.
Technical specifications
| Gasket bore | Thickness | Gasket volume | Gasket type OEM not specified |
Brand | Part number |
| 91.3 mm | 1.30 mm | 8.51 | MLS | Cometic | C5298-051 |
| 91.3 mm | 1.30 mm | 8.51 | MLS | Cometic | C5866-051 |
Gasket volume is the space it leaves open above each cylinder; it enlarges the combustion chamber and lowers the compression ratio. Comparison only makes sense between gaskets of equal bore.
Preparation and fitting
| Fasteners | Engines | Tightening torque |
| Original cylinder head bolts | LD9 | not published by the manufacturer |
Before fitting, check with a straightedge that the head and block are flat, and have them resurfaced if needed. Cometic inspects every MLS gasket before shipping; apply no sealing paste.
Technical guide
The construction offered
![]() |
Cometic MLS Stamped, riveted stainless steel sheets stacked in three layers. The outer sheets carry active beads around each cylinder and each fluid passage. It seals with a moderate clamping load and distorts the bore little. Suited from the prepared naturally aspirated engine to moderate boost. |
Choosing bore and thickness
Gasket bore. The Cometic MLS gaskets exist in 91.31 mm (C5298-051 and C5866-051), with no other bore.
Thickness. For the original gasket, the manufacturer states no thickness. A thicker gasket enlarges the combustion chamber and lowers the compression ratio; a thinner one reduces it and raises the ratio.
| Your goal | Thickness to choose |
| Keep the original compression ratio | Original thickness not published: measure that of the removed gasket and set it against the only gasket offered, 1.30 mm |
| Skimmed cylinder head, make up the lost height | Only one thickness exists, 1.30 mm: set it against that of the removed gasket, plus the material taken off when resurfacing |
| Forced induction build, lower the ratio | 1.30 mm, when the thickness measured on the removed gasket is lower |
| Naturally aspirated build, raise the ratio | 1.30 mm, when the thickness measured on the removed gasket is higher |
With no known original thickness, use a dial gauge to read how far the pistons protrude above the block face, above all if the removed gasket is thicker than 1.30 mm: this figure gives the clearance left between piston and head.
The brand
| Cometic Gasket, Inc., an American company founded in 1989 in Concord, Ohio, designs gaskets and sealing solutions for engines. It became known for made-to-measure gaskets, cut to the bore and thickness wanted, made in the United States from American raw materials. |
Advantages over the original gasket
| Criterion | Original gasket, part number not published | Reinforced gaskets |
| Construction | Construction not stated by the manufacturer | Multilayer stainless steel (MLS), three layers |
| Gasket bore | not published by the manufacturer | 91,31 mm |
| Thicknesses available | thickness not published by the manufacturer | 1.30 mm |
| Compression ratio adjustment | None | Through the thickness chosen |
| Resistance to overpressure | Limited to standard output | Designed for forced induction |
When a reinforced gasket becomes necessary
- Adding forced induction, or raising boost on an already turbocharged engine
- Cylinder rebored beyond what the 91.31 mm bore of the gaskets offered covers
- Looking for a compression ratio different from standard, higher or lower
- Engine that has already lost its gasket, or is consuming coolant
- Competition use, where the gasket goes through repeated temperature rises
Vehicle compatibility
| Model | Engine code | Power | Years |
| Buick Skylark | LD9 | not published | 1996-1998 |
| Chevrolet Cavalier | LD9 | not published | 1996-2001 |
| Chevrolet Malibu | LD9 | not published | 1997-1999 |
| Oldsmobile Achieva | LD9 | not published | 1996-1998 |
| Oldsmobile Alero | LD9 | not published | 1999-2001 |
| Pontiac Grand Am | LD9 | not published | 1996-2001 |
| Pontiac Sunfire | LD9 | not published | 1996-2001 |
OEM part number: not published by the manufacturer.
Important: C5298-051 suits LD9 engines with exhaust gas recirculation (EGR), C5866-051 those without: check whether your engine has EGR before ordering.
Why switch to a reinforced gasket?
When the original gasket is no longer enough, the reinforced gasket takes over: under higher combustion pressure it keeps its shape instead of crushing.
When the engine is pushed, with a turbo, a supercharger or a higher compression ratio, the head gasket is often the first part to fail. A reinforced gasket prevents the leak, and the head removal that would follow costs far more than the part.
-
Brand
-
ReferenceC5298-051
