Skip to content
  • On order
Reinforced head gasket Jaguar 3.8 7R TU - C4305-043 Reinforced head gasket Jaguar 3.8 7R TU - C4305-043 Reinforced head gasket Jaguar 3.8 7R TU - C4305-043 Reinforced head gasket Jaguar 3.8 7R TU - C4305-043

Reinforced cylinder head gasket Jaguar 3.8 L 7R and TU

€156.30 (tax incl.)
€208.40 (tax incl.) -25%

Reinforced Cometic head gasket in MLS and CFM-20 for the Jaguar XK inline-six engines of 3.8 litres. Sold individually.

  • Engines: 7R, TU
  • Bores: 87 to 89 mm
  • Thicknesses: 0.457 to 3.556 mm
C4305-043
0 in stock in France
ORDER TODAY, WE SHIP IN 3 WEEKS
Pay in installments

The Jaguar engines covered

The Jaguar XK inline six of 3.8 litres, identified by the codes 7R and TU, powers the E-Type Series 1, Mark II, Mark IX, Mark X, S-Type and XK 150 models detailed below.

None of our sources confirms an original gasket part number for these engines, so the standard bore, construction and thickness are left unstated. The standard gasket is sized for the original combustion pressure: once that pressure climbs, clamping is lost, the head lifts and coolant seeps into a cylinder.

Reinforced cylinder head gaskets

Sealing does not depend on the gasket alone: the fasteners that clamp the head onto the block matter just as much. Beyond 100 N/mm², a composite gasket takes a permanent set; the 301 stainless steel of MLS gaskets withstands 517 N/mm², five times more, and springs back with every combustion.

This page gathers the part numbers of Cometic, an American maker of competition gaskets, in two constructions: the multi-layer steel MLS and the CFM-20, with a steel core covered by an asbestos-free compound. The bores are 87, 88, 88.5 and 89 mm and the thicknesses run from 0.457 to 3.556 mm, enough to adjust the compression ratio without touching the pistons or the cylinder head. As a rule, the gasket bore chosen is at least 0.5 mm larger than the actual cylinder bore. Each part number is sold individually, one gasket per engine.

Technical specifications

Gasket bore Thickness Gasket volume Gasket type
OEM not specified
Brand Part number
87 mm 1.09 mm 6.48 CFM-20 Cometic C4305-043
87 mm 1.50 mm 8.92 CFM-20 Cometic C4305-059
88 mm 0.69 mm 4.20 MLS Cometic C4282-027
88 mm 0.76 mm 4.62 MLS Cometic C4282-030
88 mm 0.91 mm 5.53 MLS Cometic C4282-036
88 mm 1.02 mm 6.20 MLS Cometic C4282-040
88 mm 1.14 mm 6.93 MLS Cometic C4282-045
88 mm 1.27 mm 7.72 MLS Cometic C14063-050
88 mm 1.27 mm 7.72 MLS Cometic H1763SP4050XP
88 mm 1.30 mm 7.91 MLS Cometic C4282-051
88 mm 1.42 mm 8.64 MLS Cometic C4282-056
88 mm 1.50 mm 9.12 CFM-20 Cometic C14041-059
88 mm 1.52 mm 9.24 MLS Cometic C4282-060
88 mm 1.68 mm 10.22 MLS Cometic C4282-066
88 mm 1.78 mm 10.83 MLS Cometic C4282-070
88 mm 1.91 mm 11.62 MLS Cometic C4282-075
88 mm 2.03 mm 12.35 MLS Cometic C4282-080
88 mm 2.13 mm 12.95 MLS Cometic C4282-084
88 mm 2.18 mm 13.26 MLS Cometic C4282-086
88 mm 2.34 mm 14.23 MLS Cometic C4282-092
88 mm 2.49 mm 15.14 MLS Cometic C4282-098
88 mm 3.05 mm 18.55 MLS Cometic C4282-120
88 mm 3.56 mm 21.65 MLS Cometic C4282-140
88.5 mm 1.27 mm 7.81 MLS Cometic C14082-050
89 mm 0.46 mm 2.86 MLS Cometic C4306-018
89 mm 0.69 mm 4.29 MLS Cometic C4306-027
89 mm 0.76 mm 4.73 MLS Cometic C4306-030
89 mm 0.91 mm 5.66 MLS Cometic C4306-036
89 mm 1.02 mm 6.35 MLS Cometic C4306-040
89 mm 1.09 mm 6.78 CFM-20 Cometic C4125-043
89 mm 1.14 mm 7.09 MLS Cometic C4306-045
89 mm 1.30 mm 8.09 MLS Cometic C4306-051
89 mm 1.42 mm 8.83 MLS Cometic C4306-056
89 mm 1.50 mm 9.33 CFM-20 Cometic C4125-059
89 mm 1.52 mm 9.46 MLS Cometic C4306-060
89 mm 1.68 mm 10.45 MLS Cometic C4306-066
89 mm 1.78 mm 11.07 MLS Cometic C4306-070
89 mm 1.91 mm 11.88 MLS Cometic C4306-075
89 mm 2.03 mm 12.63 MLS Cometic C4306-080
89 mm 2.13 mm 13.25 MLS Cometic C4306-084
89 mm 2.18 mm 13.56 MLS Cometic C4306-086
89 mm 2.34 mm 14.56 MLS Cometic C4306-092
89 mm 2.49 mm 15.49 MLS Cometic C4306-098
89 mm 3.05 mm 18.97 MLS Cometic C4306-120
89 mm 3.56 mm 22.15 MLS Cometic C4306-140

A gasket's volume is the free space it leaves over each cylinder. It is added to the combustion chamber and lowers the compression ratio all the more as it grows. Only gaskets of the same bore can be compared with one another.

Preparation and fitting

Fasteners Engines Tightening torque
Original cylinder head bolts 7R, TU not published by the manufacturer

At assembly, first check the flatness of the head and the block with a straightedge, and have whichever of the two is warped machined true. No gasket sealant is needed: Cometic gaskets are supplied already coated.

Technical guide

The two constructions offered

CFM-20 Cometic
A galvanized steel core covered on both faces with a soft asbestos-free compound. This laminated construction, part metal and part fibre, combines the strength of steel with the softness of the compound. It is offered here in three bores, 87, 88 and 89 mm, and in two thicknesses, 1.09 and 1.50 mm.
Cometic MLS cylinder head gasket MLS Cometic
A stack of stainless steel plates, embossed and riveted together. The outer plates carry active beads around every cylinder and every fluid passage. A moderate clamping load is enough to seal, and the bore distorts very little. This all-round construction suits anything from a tuned naturally aspirated engine to modest boost.

Choosing bore and thickness

Gasket bore. Cometic MLS is offered in 88 mm (C4282, C14063-050, H1763SP4050XP), in 88.5 mm (C14082-050) and in 89 mm (C4306); the CFM-20 in 87 mm (C4305), in 88 mm (C14041-059) and in 89 mm (C4125).

Thickness. No original thickness is confirmed for these engines. A thicker gasket enlarges the combustion chamber and lowers the compression ratio; a thinner one reduces it and raises the ratio.

Your goal Thickness to choose
Keep the original compression ratio Standard thickness unrecorded: measure the removed gasket, then use the closest figure between 0.457 and 3.556 mm
Skimmed cylinder head, make up the lost height From 0.457 to 3.556 mm, keep the thickness of the removed gasket and add the material the resurfacing took off
Forced induction build, lower the ratio 3.556 mm, if the removed gasket is thinner
Naturally aspirated build, raise the ratio 0.457 mm, if the removed gasket is thicker

Before settling on a thickness below the original, use a dial gauge to read how far the pistons stand proud of the block face: that figure sets the clearance left between piston and head.

The brand

Cometic Cometic Gasket, Inc. is a US company founded in 1989 in Concord, Ohio, that specialises in engine gaskets and sealing solutions. Its reputation rests on the made-to-measure gasket, cut to the bore and thickness requested and manufactured entirely in the United States from American raw materials.

Advantages over the original gasket

Criterion Original gasket not confirmed Reinforced gaskets
Construction Construction not stated by the manufacturer Multi-layer stainless steel (MLS)
Gasket bore not confirmed 87, 88, 88.5 and 89 mm
Thicknesses available thickness not confirmed 0.457 to 3.556 mm, 22 values
Compression ratio adjustment None Through the thickness chosen
Resistance to overpressure Limited to standard output Designed for forced induction

When a reinforced gasket becomes necessary

  • Adding forced induction, or raising boost on an already turbocharged engine
  • Cylinder rebored beyond what the bore of the gaskets offered (87 to 89 mm) covers
  • Looking for a compression ratio different from standard, higher or lower
  • Engine that has already lost its gasket, or is consuming coolant
  • Competition use, where the gasket goes through repeated temperature rises

Vehicle compatibility

Brand Model Engine code Power Years
JAGUAR E-TYPE 3.8 (Series1) Coupé 7R 265 hp 04.1961 - 07.1964
JAGUAR E-TYPE Convertible 3.8 (Series1) Décapotable 7R 265 hp 04.1961 - 07.1964
JAGUAR Mk II 3.8 S Berline tricorps 7R 223 hp 09.1959 - 09.1966
JAGUAR Mk IX 3.8 Berline tricorps 7R 223 hp 10.1958 - 07.1961
JAGUAR S-TYPE I 3.8 Berline tricorps 7R 223 hp 05.1963 - 08.1968
JAGUAR XK Coupé 150 7R 269 hp 09.1957 - 10.1960
JAGUAR XK Coupé 150 S 7R 223 hp 09.1957 - 10.1960
JAGUAR XK Décapotable 150 7R 269 hp 09.1957 - 10.1960
JAGUAR XK Décapotable 150 S 7R 223 hp 09.1957 - 10.1960
JAGUAR Mk X MK I 3.8 Berline tricorps TU 268 hp 10.1961 - 10.1964

OEM part number: no confirmed original part number.

Important: the gaskets on this page are listed for the 3.8 litre XK engine in the survey below, at Jaguar. For any other vehicle, find the engine code first before placing an order.

Why switch to a reinforced gasket?

When the standard gasket has reached the end of its tether, the reinforced gasket steps in: under higher combustion pressure it keeps its geometry instead of crushing.

Add a turbo or a supercharger, or raise the compression ratio, and the head works harder while the gasket becomes the first weak point of the top end. A reinforced gasket prevents the leak of gas or coolant and the head removal that follows, with the car off the road.

16 other products in the same category

Viewed products

Loading...