Skip to content
  • In stock
Crankshaft thrust washers Ford Cosworth YB and Pinto 2.0 Crankshaft thrust washers Ford Cosworth YB and Pinto 2.0

Crankshaft thrust washers Ford Cosworth YB and Pinto 2.0

€11.80 (tax incl.)
€13.12 (tax incl.) -10%

Crankshaft thrust washers for the Ford Cosworth YB and Pinto 2.0 SOHC engines.

  • Brands: ACL
  • Fits: Ford, all models
  • Engine codes: Cosworth YB, Pinto 2.0 SOHC
2T2167-STD
119 in stock in Europe (72h lead time)
Pay in installments

The Ford Cosworth YB and Pinto 2.0 SOHC engines

The manufacturer lists these thrust washers for the Ford 2.0 litre Cosworth YB four-cylinder and for the Ford Pinto 2.0 SOHC. It publishes them for all models fitted with these engines. The Cosworth YB is a turbocharged inline four-cylinder of 1993 cc, introduced in 1986 on the Sierra RS Cosworth; the Pinto 2.0 is an inline four-cylinder with a cast-iron block and a belt-driven overhead camshaft.

Thrust washers

The thrust washers take the clutch thrust and set the crankshaft end float. On a modified engine with a reinforced clutch, this thrust increases. The uncoated ACL version is offered in the original size and in an oversize of 0.005 inch (+0.127 mm).

Fitted on either side of a main bearing, the half washers hold the crankshaft in its axial position. They work every time the clutch is disengaged, when the clutch pushes the crankshaft against them. A worn washer lets the end float increase and the crankshaft shift, at the expense of its own thrust faces.

Technical specifications

Part numberBrand and treatmentSizeInner Ø (mm)Outer Ø (mm)Thickness (mm)Material
2T2167-STD ACL - Uncoated Standard - - - -
2T2167+005 ACL - Uncoated +0.127 mm (0.005 inch) - - - -
Manufacturer notes
ACL
Upper and lower halves (“Half type: Upper & Lower”)

Technical guide

The lubrication grooves, present on one face of the half washer only, must face the crankshaft; the plain face rests against the block or cap. A reversed washer starves the crankshaft's thrust face of oil and damages it quickly.

Before fitting the cap, apply assembly grease to the crankshaft-side face and check that the half washers in the block are flush. The cap goes on without forcing and is then tightened according to the manufacturer's procedure. Finish by checking the end float with a dial gauge, to be compared with the manufacturer's value.

The brand

ACL ACL Bearing Company, an Australian manufacturer of high-performance engine bearings since 1949, supplies uncoated thrust washers for these engines.

Construction and advantages

Criterion ACL
Presentation Upper and lower halves
Country of manufacture Australia
Material
Coating No
Available sizes Standard, +0.127 mm (0.005 inch)

Vehicle compatibility

These thrust washers fit the Ford Cosworth YB and Pinto 2.0 SOHC engines (engine codes Cosworth YB, Pinto 2.0 SOHC) of the following vehicles:

BrandModel (chassis)Engine codePowerYears
Ford All models Cosworth YB
Ford All models Pinto 2.0 SOHC

Why replace the thrust washers

Half washers are inexpensive parts, but their wear is costly: excessive end float lets the crankshaft move at every disengagement and attacks its thrust faces, which then have to be machined, if the crankshaft does not need replacing. Changing them whenever the bottom end is opened, and always with an uprated clutch, avoids that expense.

14 other products in the same category

Viewed products

Loading...