Skip to content
  • In stock
Reinforced head gasket Ford Cosworth YB N5F - C4350-045 Reinforced head gasket Ford Cosworth YB N5F - C4350-045 Reinforced head gasket Ford Cosworth YB N5F - C4350-045 Reinforced head gasket Ford Cosworth YB N5F - C4350-045

Reinforced head gasket Ford Sierra Escort RS Cosworth 2.0 16V Turbo YB N5

€113.59 (tax incl.)
€151.45 (tax incl.) -25%

Reinforced Athena and Cometic head gasket, in Cut Ring, MLS and MLX for Ford Cosworth YB. Sold individually.

  • Brands: Athena, Cometic
  • Engines: YBB, YBD, N5B, N5C, N5D, N5F, N9C
  • Bores: 87 to 96 mm
  • Thicknesses: 0.69 to 3.56 mm
  • Replaces: YB0611
C4350-045
3 in stock in Europe (72h lead time)
Pay in installments

The Ford engines covered

The Ford YB is the 2.0-litre 16-valve DOHC turbocharged inline four-cylinder petrol engine designed by Cosworth for the Sierra and Escort RS Cosworth. This page covers its YBB and YBD versions and the N5B, N5C, N5D and N5F codes; Athena adds the N9C.

Ford does not publish an original part number for this gasket; Cosworth lists it as YB0611 (Group A gasket), superseded by YB1261. Cosworth publishes neither its construction nor its thickness; its bore is 92.5 mm. It is sized for standard combustion pressure: when that pressure rises, clamping load drops, the cylinder head lifts, and coolant passes into a cylinder.

Reinforced cylinder head gaskets

A cylinder head gasket does not create the seal on its own: it holds because the fasteners clamp the head against the block. A composite gasket is crushed for good beyond 100 N/mm² of admissible stress, whereas the 301 stainless steel of the MLS and MLX gaskets withstands 517 N/mm², 5 times more, and springs back at every combustion.

This page brings together the part numbers from two racing manufacturers, Athena and Cometic, in four constructions: Athena Cut Ring with stainless rings, Athena MLS with Gas Stopper, Cometic MLS multi-layer steel and Cometic MLX with a chamber stopper. Gasket bores run from 87 to 96 mm, covering the standard block as well as the rebored block, and thicknesses from 0.69 to 3.56 mm, enough to adjust the compression ratio without touching the pistons or the cylinder head. As a rule, the gasket bore chosen is at least 0.5 mm larger than the actual cylinder bore. Each part number is sold individually, one gasket per engine.

Technical specifications

Gasket bore
OEM 92.5 mm
Thickness Gasket volume Gasket type
OEM not specified
Brand Part number
OEM YB0611
87 mm 1.02 mm 6.06 MLX Cometic C14060-040
91.4 mm 1.30 mm 8.53 Cut Ring Athena 330029R
92.1 mm 1.30 mm 8.66 Cut Ring Athena 330030R
92.1 mm 2.00 mm 13.32 Cut Ring Athena 330046R
92.5 mm 0.69 mm 4.64 MLS Cometic C4350-027
92.5 mm 0.76 mm 5.11 MLS Cometic C4350-030
92.5 mm 0.91 mm 6.12 MLS Cometic C4350-036
92.5 mm 1.00 mm 6.72 MLS Athena 338048R
92.5 mm 1.02 mm 6.85 MLS Cometic C4350-040
92.5 mm 1.14 mm 7.66 MLS Cometic C4350-045
92.5 mm 1.15 mm 7.73 MLS Athena 338045R
92.5 mm 1.20 mm 8.06 MLS Athena 338431FR
92.5 mm 1.30 mm 8.74 Cut Ring Athena 330063R
92.5 mm 1.30 mm 8.74 MLS Athena 338042R
92.5 mm 1.30 mm 8.74 MLS Cometic C4350-051
92.5 mm 1.42 mm 9.54 MLS Cometic C4350-056
92.5 mm 1.52 mm 10.21 MLS Cometic C4350-060
92.5 mm 1.68 mm 11.29 MLS Cometic C4350-066
92.5 mm 1.78 mm 11.96 MLS Cometic C4350-070
92.5 mm 1.91 mm 12.84 MLS Cometic C4350-075
92.5 mm 2.03 mm 13.64 MLS Cometic C4350-080
92.5 mm 2.13 mm 14.31 MLS Cometic C4350-084
92.5 mm 2.18 mm 14.65 MLS Cometic C4350-086
92.5 mm 2.34 mm 15.72 MLS Cometic C4350-092
92.5 mm 2.49 mm 16.73 MLS Cometic C4350-098
92.5 mm 3.05 mm 20.50 MLS Cometic C4350-120
92.5 mm 3.56 mm 23.92 MLS Cometic C4350-140
93.5 mm 1.00 mm 6.87 MLS Athena 338047R
93.5 mm 1.02 mm 7.00 MLS Cometic C14035-040
93.5 mm 1.15 mm 7.90 MLS Athena 338044R
93.5 mm 1.30 mm 8.93 MLS Athena 338041R
94 mm 1.02 mm 7.08 MLS Cometic H1267SP8040S
94 mm 1.30 mm 9.02 MLS Cometic H1267SP8051S
94 mm 2.03 mm 14.09 MLS Cometic H1267SP8080S
94.5 mm 1.15 mm 8.07 MLS Athena 338043R
94.5 mm 1.30 mm 9.12 MLS Athena 338040R
95.5 mm 1.30 mm 9.31 MLS Cometic H2703SP1051S
96 mm 1.30 mm 9.41 MLS Cometic H1267SPL051S

Gasket volume: the space the gasket leaves above each cylinder. It enlarges the combustion chamber, and the larger it is, the lower the compression ratio. Values compare with one another at identical gasket bore.

Preparation and fitting

Fasteners Engines Tightening torque
Original cylinder head bolts
SC1200A
YBB Not published
ARP cylinder head studs
ARP-251-4701
YBB, YBD, N5B 41 Nm, then 81 Nm, then 122 Nm

Before fitting, check the flatness of the cylinder head and of the block with a straight edge and have them skimmed if necessary. None of these gaskets requires sealant: Athena and Cometic both supply them already coated.

Reinforced ARP cylinder head studs Ford Cosworth YB N5B →

Technical guide

The three constructions offered

Athena Cut Ring cylinder head gasket Athena Cut Ring
A gasket in reinforced, asbestos-free MO115 material (steel core, aramid fibres, NBR binder), supplied with separate AISI 304 stainless steel rings around each cylinder. Athena also intends it for turbocharged or nitrous engines above 2 bar, with no machining of the cylinder head or block. A silicone bead reinforces the sealing of the water and oil passages. On fitting, the ring embossments face the cylinder head. Athena rates the MO115 material at 100 N/mm² at most: the stainless rings are what hold combustion.
Athena MLS cylinder head gasket Athena MLS
Two to five layers of AISI 301 stainless steel, laser cut, stamped and riveted. Around each cylinder, a layer folded over on itself, the Gas Stopper, concentrates the clamping load on the combustion chamber, while beads seal the water and oil passages. The outer layers receive a two-coat finish: the first withstands high temperatures and fills small irregularities on the block and cylinder head, the second, silicone based, keeps the gasket from sticking on disassembly. This is Athena's all-steel choice, from a prepared naturally aspirated engine to moderate forced induction.
Cometic MLS cylinder head gasket Cometic MLS
Several stamped and riveted stainless steel layers. The outer layers carry active beads around each cylinder and each fluid passage. Sealing is achieved with a moderate clamping load and limited bore distortion. This is the versatile choice, from a prepared naturally aspirated engine to light forced induction.
Cometic MLX cylinder head gasket Cometic MLX
The same base as the MLS, with a folded centre layer forming a stopper around the combustion chamber and a high-temperature coating. Local clamping increases without adding bore distortion. It is the most resistant of the all-steel gaskets, to be chosen when boost goes beyond what an MLS can hold, in 87 mm.

Choosing bore and thickness

Gasket bore. The Athena Cut Ring comes in 91.4, 92.1 and 92.5 mm, the Athena MLS in 92.5, 93.5 and 94.5 mm, the Cometic MLS in 92.5, 93.5, 94, 95.5 and 96 mm, the Cometic MLX in 87 mm.

Thickness. Cosworth does not publish the thickness of the original gasket. A thicker gasket enlarges the combustion chamber and lowers the compression ratio; a thinner one reduces it and raises the ratio.

Your goal Thickness to choose
Keep the original compression ratio The value closest to the thickness of the removed gasket
Skimmed cylinder head, make up the lost height The thickness of the removed gasket + what was removed
Forced induction build, lower the ratio A thickness above that of the removed gasket
Naturally aspirated build, raise the ratio A thickness below that of the removed gasket

With a thickness finer than that of the removed gasket, measure piston protrusion above the block with a dial gauge: it is what determines the remaining clearance between piston and cylinder head.

The two brands

Athena Athena S.p.A. is an Italian manufacturer of engine gaskets and components, with its head office and main plant in Alonte, in the Veneto region. The group also produces in Spain, the United States, Brazil and India. Its multi-layer gaskets are fitted as original equipment by car manufacturers, and its racing range is designed and made entirely in Italy.
Cometic Cometic Gasket, Inc. is an American manufacturer of engine gaskets and sealing solutions, founded in 1989 and based in Concord, Ohio. Its speciality is the made-to-order gasket, in the bore and thickness required. All its products are made in the United States, from American materials.

Advantages over the original gasket

Criterion Original gasket YB0611 Reinforced gaskets
Construction Not specified by the manufacturer Multi-layer stainless steel
Gasket bore 92.5 mm 87 to 96 mm
Thicknesses available Not published by Cosworth 0.69 to 3.56 mm, 22 values
Compression ratio adjustment None Through the thickness chosen
Resistance to overpressure Limited to standard output Designed for forced induction

When a reinforced gasket becomes necessary

  • Adding forced induction, or raising boost on an already turbocharged engine
  • Cylinder rebored beyond what the 92.5 mm bore of the original gasket covers
  • Looking for a compression ratio different from standard, higher or lower
  • Engine that has already lost its gasket, or is consuming coolant
  • Competition use, where the gasket goes through repeated temperature rises

Vehicle compatibility

Model Engine code Power Years
Ford Escort V (AAL, ABL) N5F 220 hp 1991-1995
Ford Escort VI (GAL, AAL, ABL) N5F 220 hp 1995-1998
Ford Sierra I (GBC) N5B, YBB 204 hp 1985-1987
Ford Sierra II (GBG, GB4) N5B, N5C, N5D, N9C, YBB 120, 125, 204, 215 and 220 hp 1987-1993
Ford Sierra II (GBC, GBG) N5B, N5C, N5D, N9C, YBB, YBD 120, 204, 220 and 227 hp 1987-1993
Ford Sierra II Turnier (BNG) N9C 120 and 125 hp 1989-1993

OEM part number: YB0611, YB1261 (Cosworth).

Important: the 8-valve Ford Pinto engines take other cylinder head gaskets: they are not covered by this page, even though Cometic also lists its C4350 series for the NEP.

Why switch to a reinforced gasket?

A reinforced gasket holds where the standard one reaches its limit: at higher combustion pressure it keeps its shape instead of being crushed.

As soon as power goes up, turbo, supercharger or raised compression ratio, the head gasket becomes the weak link of the top end. Switching to a reinforced gasket is then not a comfort but a safeguard: it is what prevents the failure and the head removal that comes with it.

14 other products in the same category

Viewed products

Loading...