Skip to content
  • In stock
ACL trimetal connecting rod bearings Porsche 911 SC 3.0 930 ACL trimetal connecting rod bearings Porsche 911 SC 3.0 930

ACL trimetal connecting rod bearings Porsche 911 SC 3.0 930

€97.37 (tax incl.)
€108.19 (tax incl.) -10%

Set of 12 trimetal connecting rod half-bearings for Porsche 930 3.0 SC.

  • Brand and treatment: ACL Race
  • Compatibility: 911 SC 3.0
  • Engine codes: codes in the compatibility table
  • Available sizes: standard to +0.25 mm, increased-clearance version (HX)
6B2462H-STD
22 in stock in Europe (72h lead time)
Pay in installments

The Porsche 930 3.0 SC flat-six engines

The 3.0-litre 930 of the Porsche 911 SC (930.03, 930.09, 930.10 and 930.19) is an air-cooled flat-six producing 180 to 204 hp. All its versions share the same crankpin diameter: a single bearing set covers the whole family.

From the factory, this engine is fitted with standard production connecting rod bearings, sized for the loads of the original engine: as soon as power, engine speed or boost pressure increase, they reach their limits.

Trimetal connecting rod bearings

In a trimetal bearing, a steel back carries a copper-lead intermediate layer with high load capacity, itself covered by an anti-friction running layer that spares the crankpin. The set is supplied complete: 12 half shells, i.e. 6 pairs.

Trimetal targets high, sustained loads, whereas aluminium bi-metal is limited to low to medium loads: about 8,000 psi for the latter, up to 12,000 psi for a performance trimetal, 50% more. The benefit shows in strength and durability on turbo, supercharged and high-revving engines.

Technical specifications

Fitment dimensions common to all references
ACL bearings
Crankpin Ø 52.971 / 52.990 mm
Housing bore Ø 56.000 / 56.019 mm
Width 17.8 mm
ReferenceBrand and treatmentSizeWall thickness (mm)
6B2462H-STD ACL Race - Untreated Standard 1.490
6B2462HX-STD ACL Race - Untreated Std, increased clearance (HX) 1.477
6B2462H-.025 ACL Race - Untreated +0.025 1.503
6B2462H-.25 ACL Race - Untreated +0.25 1.615

Running clearance

Running clearance is the gap between the bearing and the crankpin, filled by the oil film.

While the engine turns, the crankpin floats on this oil film, which carries the load without direct contact with the bearing. Film thickness depends on clearance: too tight, oil passes poorly, temperature rises and the risk of seizure grows; too wide, oil escapes, the film carries less and oil pressure decreases. A correct clearance ensures both sufficient lubrication and a well-maintained film.

Size / gradeWhen to choose itACL Race Series
Standard (STD) Standard journal, not reground 0.055 to 0.066 mm
Increased clearance (HX) Wider clearance: high oil flow, high rpm 0.080 to 0.091 mm
+0.025 mm Polished journal 0.055 to 0.066 mm
+0.25 mm Journal reground to 0.25 mm 0.055 to 0.066 mm

Checking on assembly: lay a calibrated strip (Plastigauge) on the journal, torque the rod cap to spec, then compare the crushed strip against the gauge to read the clearance.

Plastigauge

Order the Plastigauge →

Technical guide

These ACL trimetal connecting rod bearings are aimed at built engines and racing: where a standard bearing quickly reaches its limit, they accept more power, more rpm and more boost. The range includes the standard size, a +0.025 mm size for a crankpin that has only been polished, a +0.25 mm regrind size and the HX version with increased clearance for high-revving engines or engines needing a high oil flow. It allows the same part number to be kept after the crankshaft is reground and the clearance to be tailored to the oil used and the engine's duty.

The brand

ACL Bearing Company An Australian specialist in high-performance engine bearings since 1949, ACL Bearing Company produces the Race Series: precisely made trimetal bearings, available in numerous sizes and recognised on built engines across the world.

Vehicle compatibility

This connecting rod bearing set fits the 930 3.0 SC flat-six engines of the following Porsche models:

BrandModel (chassis)Engine codePowerYears
PORSCHE 911 3.0 SC 930.10 204 hp 1980–1983
PORSCHE 911 3.0 SC Carrera 930.03, 930.09, 930.19 180–188 hp 1977–1980
PORSCHE 911 Convertible 3.0 SC 930.10 204 hp 1982–1983
PORSCHE 911 Targa 3.0 SC Carrera 930.03, 930.09, 930.19 180–188 hp 1977–1980

Why replace the bearings

Replacing the bearings during a build or rebuild guards against the most expensive failure: a worn-out connecting rod bearing scores the crankpin, contaminates the oil circuit with debris and forces at least a crankshaft regrind, or even a new rod and block. Against such costs a new set weighs little: it is the cheapest part of the rotating assembly, but the one whose failure costs the most.

6 other products in the same category

Viewed products

Loading...