Categories
Manufacturers
Categories
kit of 2 three-hole steel flanges for weld-on fittings for 57mm diameter tubing, gasket and screws from NSB CONCEPT. Genuine performance automotive part. Fast shipping. Key specs: kit 2 flanges 3 holes 57mm weld Information Flange material ST37 steel Gasket aluminum 5754 Dimensions see photo Delivered with.
POWERSPRINT flat reinforced universal silent block for exhaust, center distance 82mmInformation:Resistance: -50A deg C / +220A deg CMaterials: Reinforced rubber siliconeDimensions: see photo
57/60.5mm - POWERSPRINT stainless steel silencer, dual inlet/single outlet, weldable, body 220x140mm, length 450mm from NSB CONCEPT. Genuine performance automotive part. Fast shipping. Key specs: Universal stainless steel silencer POWERSPRINT weldable with pipes inner diameter 57mm and 60 5mm length 450mm body 220x140mm outer.
47/60.5mm - POWERSPRINT stainless steel silencer, dual inlet/single outlet, weldable, body 220x140mm, length 450mm from NSB CONCEPT. Genuine performance automotive part. Fast shipping. Key specs: Universal stainless steel silencer POWERSPRINT weldable with pipes inner diameter 47mm and 60 5mm length 450mm body 220x140mm outer.
Symmetrical conical stainless steel reducer, diameter 127-60.3mm, length 200mm, thickness 1.5mm
Flapper / Exhaust ValveInformation:Inner diameter: 63.5mmControl: by pressure / gas flowMaterials: stainless steelResistance temperature: -40A deg C / +650A deg COpen at rest
Stainless steel flange with 3 screws and connecting pipe, outer diameter 55mm, length: 100mm
Gasket for 3-hole flange, 89mm diameter, 3mm thickness
Stainless steel 2-hole weld flange for 89mm diameter pipe, 8mm thicknessGeneric photo, flange sold individually
RTD type EGT AEM exhaust gas temperature probe. NSB CONCEPT. Fast shipping!
SYTEC 340 L/H High Flow E85 Petrol Pump
MALPASSI Adjustable Fuel Pressure Regulator for BMW 535i (E34) 88-95For fuel-injected engines only. This pressure regulator is adjustable, allowing you to increase your engine's performance. It installs in place of the original part.Image for illustrative purposes only
Hard silent block insert Powerflex PerformaNCe for upper right engine mount for RENAULT
Reinforced engine mount VIBRA-TECHNICS Sport part number FOR21MPrice for one mount
High impedance fuel injector clinic 365cc, 53mm length, 14mm fuel rail diameter, 15mm intake manifold diameter, EV6 connector (USCAR)
Muffler pipe stainless steel RC RACING for SEAT LEON 2.0 TFSI BWJ 240cv 11/2006 - 05/2011
High-quality Forged connecting rods ABARTH FIAT 500 large PUNTO 1.4 T-JET (Forged connecting rods ABARTH FIAT 500 large PUNTO) for reliable fitment and performance.
RC RACING Group N silencer made of 304L stainless steel, with wide welds and tight tolerances allowing for easy installation in place of the original part.As an Official Distributor, we can offer custom manufacturing (modification of pipe and outlet diameter, manifold flange modification, vehicle/competition specifications, etc.).Not road legal.
BREEZY 235mm 13-row matrix oil cooler kit, DASH10 male connections with 85A deg C MOCAL thermostatic sandwich plate
REDOX silicone coupling sleeve, 11mm inner diameter, 76mm length
Silicone reducer 90A REDOX, internal diameters 67-76mm, length 125x125mm
45A silicone elbow, REDOX, 11mm inner diameter, 100x100mm length
COOL IT Clamp-on Thermal Insulation 15.24 x 60.96cm for PipeReduces heat transfer (blocks 95% of radiant heat).Generic Photo
COOL IT Generation 2 Copper Thermal Insulation Tape for ExhaustReduces heat loss, providing several advantages:Limits the temperature in the engine compartmentReduces the risk of combustion of components near the exhaustThe heat flow is optimized: better exhaust gas evacuation and therefore better efficiencySpecifications:Width: 50.8mm (2")Length: 15.24m...
RENAULT Megane 3 RS discs 340mm 2.0 16V Turbo F4R 11/2008- pads brake front FERODO DSUNO (set) from NSB CONCEPT. Genuine performance automotive part. Fast shipping. Key specs: FERODO DSUNO front brake pads set for RENAULT M gane 3 RS 340mm discs 2 0 16V Turbo F4R engine.
FERREA Exhaust Valve 33x5.96x104.75mm (+1mm) Competition More, reference F1519P - Sold individually Technical Specifications:
kit of 4 rods + 4 retaining pins for HISPEC Ultralite 2 and 4 calipers
Large format MOCAL sandwich plate
M8x125 Stainless Steel Bleed ScrewThread: M8x125 Material: Stainless Steel Image for illustrative purposes only
Crankshaft ACL side bearings for NISSAN 200SX S14 SILVA S15 SR20DET
Goodridge braided brake hose kit for Peugeot RCZ, all models except "R" version
Dummy aluminum hose nut for DASH 10 hose, red hose clamp, for 200 Series Dash 10 hose
RC RACING stainless steel intake manifold with lambda sensor port for PEUGEOT 205 GTI 1.9 Catalytic Converter 122hp 105hp
SAFFA Reinforced Clutch Mechanism for PEUGEOT 405 Mi16, 1.9 16V engine from 1988 to 1992For 215mm diameter discPull-type clutchThe reinforced mechanisms have the same dimensions and tolerances as the standard series, but with increased pressure plate and damping tabs Reinforced. Photo not contractual
SAFFA 3-pad sintered metal reinforced clutch disc for SUZUKI Samurai SJ413, 1.3 8V engine from 1989 to 2003Technical Information:Diameter: 190mmNumber of splines: 20 Disc compatible with original mechanism but Attention Your original mechanism will wear out faster than a reinforced mechanism.
Modine silicone REDOX hose for water/oil heat exchanger for PEUGEOT 205 Automatic from 1986 to 1995. Supplied with hose clamps.
SAFFA rigid sintered metal reinforced clutch disc with 4 pads for PEUGEOT 306, 2.0 16V engine from 1999 to 2001Technical Information:Diameter: 215mmNumber of splines: 18 Disc compatible with original mechanism but caution Your original mechanism will wear out faster than a reinforced mechanism.
SAFFA 4-pad sintered metal reinforced clutch disc for PEUGEOT 106 S16, 1.6 16V engine from 1991 to 2003Technical Information:Diameter: 200mmNumber of splines: 18 Disc compatible with original mechanism but note your original mechanism will wear out faster than a new one reinforced.
Fiber-to-metal gasket for compensator, 65mm diameterGasket dimensions:Inner diameter: 66.5mmThickness: 14mm
Stainless steel flange with 2 screws and connecting pipe, outer diameter 65mm, length: 100mm
Cylinder head gasket ATHENA bore 85.3mm FIAT 1.4 146A8 1.6 159A3 LANCIA 2.0 8V 16V HF
SAFFA Reinforced Clutch Disc, Reference EMB-6104Technical Information:- Diameter: 240mm- Disc: Rigid- Pads: 6 sintered metal pads- Hub: 24.1 x 21.8 x EV- Splines: 23
CITROEN Saxo with airbag Hub flywheel OMP. NSB CONCEPT. Fast shipping!
OMP Steel Upper Front Strut Brace for Volvo 850 2.0 20V / Turbo 20V
RC RACING 4-in-1 stainless steel manifold screw kit (2 screws) for VOLKSWAGEN POLO 1.4 8V 00-
4-into-1 manifold with stainless steel connecting pipe from RC RACING, manufactured from 304L stainless steel, with wide welds and tight tolerances for easy installation in place of the original part.As an Official Distributor, we can offer custom manufacturing (modification of pipe and outlet diameters, manifold flange modifications, vehicle/competition...
RC RACING stainless steel intermediate pipe made from 304L stainless steel, with wide welds and tight tolerances for easy installation in place of the original part.As an Official Distributor, we can offer custom manufacturing (modification of pipe and outlet diameter, modification of manifold flange, vehicle/competition specifications, etc.).NOT APPROVED...
Known as "inter IRESA", here you will find the RC RACING TI-01BS stainless steel exhaust mid-pipe, manufactured in Spain, for which NSB CONCEPT has been an official distributor since 2009
Known as the "IRESA silencer", here you will find the RC RACING and244-73 stainless steel exhaust silencer, manufactured in Spain, for which NSB CONCEPT has been an official distributor since 2009
KING RACE side bearings, reference: TW 133AM
bearings lateraux KING RACE NISSAN 350Z 3.5 VQ35of. NSB CONCEPT. Fast shipping!
Crankshaft side bearings King Racing for NISSAN 200SX S14 SILVA S15 SR20DET
High-quality Tri-Metal Connecting Rod Bearings ACL RACE/KING RACING Suzuki 1.6 125CV M16A (Tri-Metal Connecting Rod Bearings ACL RACE/KING RACING Suzuki) for reliable fitment and performance.
High-quality Reinforced Valve Springs VW Golf 3 VR6 2.8 AAA (Reinforced Valve Springs VW Golf VR6 2.8 AAA) for reliable fitment and performance.
16mm ISB ball Gasket, male M16x200, left-hand thread