Skip to content
  • On order
Reinforced exhaust valves BMW M5 F10 M6 F13 S63B44B Reinforced exhaust valves BMW M5 F10 M6 F13 S63B44B

Reinforced exhaust valves BMW M5 F10 M6 F13 S63B44B

€1,115.94 (tax incl.)
€1,394.93 (tax incl.) -20%

Set of 16 reinforced exhaust valves for BMW S63B44B.

  • Brand: SUPERTECH
  • Engine: S63B44B (M5 F10, M6 F06, F12, F13)
  • Dimensions: 29 mm head, 106 mm length
  • Material: sodium filled Inconel, single groove
BMEVI-1063S-HS-16
0 in stock in France
ORDER TODAY, WE SHIP IN 5 - 15 DAYS
Pay in installments

BMW engines covered

Designed by BMW M, the S63B44B is a 4,395 cc twin turbo V8 with an 89 mm bore and an 88.3 mm stroke. It powers the M5 F10 from 2011, then the M6 F06, F12 and F13 from 2012.

Until 07/2015, its 16 original exhaust valves are BMW 11 34 7 609 942, with a 29.0 mm head and a 5.92 mm stem, held by the 11 34 1 461 405 collets. Every rise in boost pressure, through a remap or larger turbos, adds to the thermal load they carry.

SUPERTECH reinforced exhaust valves

Releasing the burnt gases and sitting right in their flow, the exhaust valve sees its head metal pass 1,000 °C on a forced induction engine such as the S63, against 760 to 870 °C when naturally aspirated. The seat draws off around 75 % of this heat and the guide around 20 %. An EV8 type exhaust steel keeps 550 MPa at 600 °C, yet only 300 MPa at 800 °C. Pushed further, the head overheats, works in fatigue, distorts and the seal on the seat deteriorates.

SUPERTECH makes the BMEVI-1063S-HS in Inconel, a nickel superalloy holding 1,100 MPa at 649 °C, 860 MPa at 732 °C and 554 MPa at 816 °C: near 800 °C that means about 85 % more strength than an EV8 steel. Its hollow stem contains sodium, which melts from 97.8 °C and carries heat from the head into the stem; the stem then sheds close to 40 %, against 25 % for a solid valve.

The 29 mm head stays that of the BMW part, so the valve replaces the original with no seat work. It is 106 mm long and has a single groove, which calls for the matching collets.

Exhaust valve technical specifications

Part numberBrandSizeHead Ø
OEM 29.0 mm
Stem Ø
OEM 6 mm
LengthGroovesMaterial
BMEVI-1063S-HS-16 SUPERTECH Standard 29 mm 6 mm 106 mm 1 Sodium filled Inconel

Valve fitting

PartBMW originalReinforced
Collets 11 34 1 461 405 (3 grooves) KPR-6S-7-32 (single groove)
Valve stem seals Kits 11 34 0 039 494 / 11 34 0 054 492 VSI-EC60E
Valve guide

The BMEVI-1063S-HS has a single groove, whereas the BMW 11 34 1 461 405 collets have three: it must be fitted with the KPR-6S-7 collets, to be ordered with the set.

The head stays at 29 mm: during the rebuild, the exhaust seats are checked and recut if needed, with no change of size.

For the valve stem seals, the BMW 11 34 0 039 494 or 11 34 0 054 492 kits, or the VSI-EC60E Viton seals, are fitted with these valves.

Technical guide

Our brand

SUPERTECH SUPERTECH Performance, a San Jose firm in Silicon Valley, has produced competition valves for over thirty years, alongside titanium retainers, springs and valve guides. Whatever the material (stainless, titanium, Inconel), each valve starts from an engine study and is validated by drag, rally and circuit tuners.

How to choose

Trapped between stem and spring retainer, the collets drop into the groove and lock the valve. Their number decides how it is retained; this engine gets a single 1 groove version, and here is how it compares:

CriterionAvailable version
Size Standard, 29 mm
Same head as the BMW valve: the seats keep their size and the swap needs no machining, in Inconel with a sodium-filled stem.
Grooves Single groove
Here the stem is gripped by the collets, the groove is relieved and the wider bearing cuts friction. Fitted with SUPERTECH KPR-6S-7 collets, never the original ones.

When reinforced valves become necessary

  • Sharper camshafts or stronger valve springs
  • Rev limiter set higher
  • Higher boost pressure or bigger turbos (Inconel recommended)
  • Cylinder head overhauled for track, drift or rally
  • Original valves burnt, pitted or down to repair size

Vehicle compatibility

ModelEngine codePowerYears
M5 (F10) S63B44B 560-568 hp 2011-2015
M5 Competition (F10) S63B44B 575 hp 2013-2015
M5 30th Anniversary (F10) S63B44B 600 hp 2014-2015
M6 (F06 / F12 / F13) S63B44B 560-568 hp 2012-2015
M6 Competition (F06 / F12 / F13) S63B44B 575-600 hp 2013-2015

OEM part number (exhaust valve): 11 34 7 609 942

Important: this set is intended for S63B44B engines built until 07/2015; after that, BMW fits another original exhaust valve (11 34 8 605 663), which is not covered on this page.

Don't forget the inlet valves

With the cylinder head off anyway, replace the valve stem seals as well as the inlet valves in one go. Below are the matching parts for this engine:

Inlet valves BMW M5 F10 M6 F13 S63B44B →
6 mm valve stem seals →

11 other products in the same category

Viewed products

Loading...