Skip to content
  • On order
PSA TU 106 XSI 8s Soupapes d'échappement Forgées 106/ saxo 8S PSA TU 106 XSI 8s Soupapes d'échappement Forgées 106/ saxo 8S

Reinforced exhaust valves BMW M3 E30 S14B23 S14B25

€248.74 (tax incl.)
€310.92 (tax incl.) -20%

Set of 8 reinforced exhaust valves for BMW M3 E30 S14B23 and S14B25.

  • Brands: SUPERTECH, CATCAMS
  • Engines: S14B23, S14B25
  • Dimensions: 32.0 mm, 32.5 mm or 33.0 mm head, 7 mm stem
  • Material: stainless steel or Inconel, 3 grooves
BMEVN-1009-8
On order, 15 to 30 days lead time
Pay in installments

BMW engines covered

The S14 is the competition four-cylinder of the BMW M3 E30: 16 valves, twin overhead camshafts and solid tappets with shims. The 2.3 litre S14B23 (93.4 mm bore, 84 mm stroke) powers the M3 from 1986 to 1991, and the 2.5 litre S14B25 (95 x 87 mm) the 1990 M3 Sport Evolution.

Each engine takes 8 exhaust valves with a 7 mm stem: BMW part number 11 34 1 309 487 on the S14B23 and 11 34 1 315 611 on the S14B25, with a 32.0 mm head and a 7.0 mm stem, a length of 123.8 mm on the S14B23 and 3-groove 11 34 1 307 136 collets. They are sized for the standard engine; a build that raises revs, load or exhaust gas temperature pushes them beyond that.

SUPERTECH and CATCAMS reinforced exhaust valves

Opening straight into the stream of burnt gases, the exhaust valve takes the highest heat in the engine. Its head metal reaches 760 to 870 °C on a normally aspirated four-cylinder like the S14, and crosses 1,000 °C once boosted. The seat removes about 75 % of it, the guide close to 20 %. Steel loses strength as it warms: an EV8-family steel, used as the yardstick, withstands 550 MPa at 600 °C yet only 300 MPa at 800 °C. Push load, revs or boost higher and the head runs hotter, fatigues, may distort and soon no longer seals.

Reinforced valves are made from materials that resist heat far better. SUPERTECH offers two of them for the S14: stainless steel with a black nitride finish, hardened at the surface and polished, which rubs and wears less in the guide, and Inconel, a nickel superalloy holding 860 MPa at 730 °C and still 554 MPa near 815 °C, nearly 85 % above the yardstick steel around 800 °C: the material to go for on a boosted S14. CATCAMS supplies a valve true to the factory dimensions, 32.0 mm head and 124.0 mm length, as a set of 8 for a rebuild close to standard.

Two oversizes are also listed: +0.5 mm with a 32.5 mm head and +1 mm with a 33.0 mm head. Only the head gains diameter; burnt gases clear out earlier and the cylinder fills better, which helps output. SUPERTECH makes them in 123.7 mm, nearest to original, and in 126.1 mm; the standard size Inconel valve measures 125.0 mm. The exhaust seats are then machined to the new size.

Exhaust valve technical specifications

Part numberBrandSizeHead Ø
OEM 32.0 mm
Stem Ø
OEM 7 mm
Length
OEM 123.8 mm
GroovesMaterial
BMEVN-1009-8 SUPERTECH +0.5 mm 32.5 mm 7 mm 123.7 mm 3 Black nitride stainless steel
BMEVN-1009L-8 SUPERTECH +0.5 mm 32.5 mm 7 mm 126.1 mm 3 Black nitride stainless steel
BMEVN-1010-8 SUPERTECH +1 mm 33.0 mm 7 mm 123.7 mm 3 Black nitride stainless steel
BMEVN-1010L-8 SUPERTECH +1 mm 33.0 mm 7 mm 126.1 mm 3 Black nitride stainless steel
BMEVI-1006L-8 SUPERTECH Standard 32.0 mm 7 mm 125.0 mm 3 Inconel
BMEVI-1010-8 SUPERTECH +1 mm 33.0 mm 7 mm 123.7 mm 3 Inconel
9213004M*8 CATCAMS Standard 32.0 mm 7 mm 124.0 mm

Valve fitting

PartBMW originalReinforced
Collets 11 34 1 307 136 (3 grooves)
Valve stem seals Kit 11 34 9 059 171 VS-VW7E-8 (exhaust)
Valve guide Inner Ø 7.0 mm H7 GDE-BMS14-7

The SUPERTECH valves on this page all have 3 grooves, like the original ones: they are fitted with 7 mm 3-groove collets, preferably new.

With a +0.5 or +1 mm oversize, the exhaust seats in the cylinder head are recut to the new dimension during the rebuild.

S14 valve clearance is set with shims: after replacing the valves, check the clearance and adjust the shims.

Technical guide

Our brands

SUPERTECH SUPERTECH, located in the heart of Silicon Valley, has been drawing up racing valves, springs, guides and retainers made of titanium for over 30 years. Stainless, titanium or Inconel alike, each valve is designed for one defined engine, then proven by circuit, rally and drag racing tuners.
CATCAMS CATCAMS, a Belgian valvetrain specialist, works out its own lift profiles and grinds its camshafts on CNC machines. Its range also includes tappets, valve springs, retainers and shims; its camshafts earned their stripes in the BTCC and at the Le Mans 24 Hours.

How to choose

Held by the retainer, the collets sit in the stem grooves and lock the valve in position. Every version listed here has 3, just like the BMW part, so the decision comes down to head diameter and material.

CriterionOption 1Option 2
Size Standard size
32.0 mm head, for cylinder head seats that were never reground. Two choices: SUPERTECH Inconel (125.0 mm) or CATCAMS (124.0 mm).
+0.5 and +1 mm oversizes
32.5 and 33.0 mm heads: the cylinder clears its burnt gases faster and draws in more fresh charge, which benefits output (around 10 to 12 cfm per mm of head). Cutting the seats to the chosen size can also recover seats already reground.
Material Black nitride stainless steel
SUPERTECH versions, surface hardened and polished, with less friction and wear in the guide. Suited to a naturally aspirated road or track S14, nothing else to modify. Offered in +0.5 and +1 mm, 123.7 or 126.1 mm long, ideally with new 3-groove collets.
Inconel
Nickel superalloy that keeps its strength beyond 800 °C, where steel weakens. SUPERTECH version for boosted engines or engines run hard at full load, the material to favour with forced induction. Available at standard size (125.0 mm) or +1 mm (123.7 mm), with 3-groove collets.

When reinforced valves become necessary

  • Sharper camshaft profiles or reinforced valve springs
  • Higher maximum revs
  • Engine converted to forced induction (Inconel version recommended)
  • Cylinder head renewed for hill climb, circuit or rally
  • Original valves pitted, bent or already recut to repair size

Vehicle compatibility

ModelEngine codePowerYears
M3 (E30) 2.3 S14B23 195-200 hp 1986-1991
M3 Evo (E30) 2.3 S14B23 220 hp 1988-1990
M3 Sport Evolution (E30) 2.5 S14B25 238 hp 1990

OEM part number (exhaust valve): 11 34 1 309 487 (S14B23); 11 34 1 315 611 (S14B25)

Important: these sets of 8 are intended for the S14 four-cylinder; the S38 six-cylinder of the M5 E34, which uses the same original valves, needs 12.

Don't forget the inlet valves

If the S14 cylinder head is fully rebuilt, renew the inlet side in the same job too, valves and valve stem seals included. Our parts for these two engines:

BMW M3 E30 S14B23 S14B25 inlet valves →
7 mm exhaust valve stem seals →

16 other products in the same category

Viewed products

Loading...