- On order
Reinforced inlet valves SUBARU EJ20 EJ205 EJ207 EJ255 EJ257
Set of 8 reinforced inlet valves for SUBARU EJ20 turbo, EJ255 and EJ257.
- Brands: SUPERTECH, FERREA
- Engines: EJ20G, EJ20U, EJ20-GN, EJ205, EJ207, EJ20X, EJ20Y, EJ255, EJ257, EJ25DET
- Dimensions: head 36 mm, 36.5 mm or 37 mm, stem 5.96 mm or 5.97 mm, length 103.85 mm to 104.6 mm
- Material: black nitride single groove stainless, chrome stem stainless or EV8 stainless with hard chrome stem
SUBARU engines covered
The EJ is Subaru's flat-four, with 16 valves and two camshafts on each cylinder head. This page covers its turbocharged versions: 2.0 litre (EJ20G, EJ20U, EJ20-GN, EJ205, EJ207, EJ20X, EJ20Y) from 170 to 320 hp and 2.5 litre (EJ255, EJ257, EJ25DET) from 211 to 400 hp. Since 1992 they have powered the Impreza WRX and WRX STi, the WRX, the turbocharged Forester and Legacy, the Outback and the Baja.
The engine has 8 inlet valves: Subaru lists them as 13201AA390, 13201AA391 then 13201AA371 on the EJ205, 13201AA510, 13201AA400 then 13201AA371 on the EJ207, and 13201AA400 then 13201AA371 on the EJ255. Their stem measures 5.955 to 5.970 mm for a length of 104.4 mm. Higher boost, sharper camshafts or more rpm load them far beyond standard use.
SUPERTECH and FERREA reinforced inlet valves
At high rpm, dozens of times each second, the inlet valve opens and closes the way in for the fresh air pushed by the turbo. Every closing slams its head against the cylinder head seat, while its stem travels back and forth non-stop in the guide. Its working temperature lies between 400 and 550 °C: at that level the chrome-silicon steel fitted as standard is already weakening, with 500 MPa of strength at 500 °C and only 250 MPa at 600 °C, barely higher, a 50 % drop. More lift, stiffer springs, higher rpm or extra boost multiply the shocks, the rubbing and the heat load.
The SUPERTECH valves offered here are black nitride stainless steel: the treatment hardens the skin of the metal and makes it smoother, cutting friction and stem wear in the guide, and a back cut under the head eases the air flow. The FERREA Competition Plus valves, stainless with a chrome stem, gain 20 % in hot strength and fatigue resistance, with a seat that lasts 25 % longer. The FERREA 6000 series uses EV8 stainless with a hard chrome stem, which keeps 650 MPa at 500 °C, 30 % more than the standard steel, and 550 MPa at 600 °C, 120 % more.
Each brand also comes with an enlarged head: 37 mm in +1 mm oversize instead of 36 mm, and 36.5 mm in +0.5 mm oversize at SUPERTECH, the stem keeping its diameter. Being wider, it opens a bigger area at the seat: air gets into the cylinder more easily and power rises, once the head seats are cut to that size.
Inlet valve technical specification
| Part number | Brand | Size | Head Ø | Stem Ø | Length | Grooves | Material |
|---|---|---|---|---|---|---|---|
| SIVN-1010-8 | SUPERTECH | Standard | 36.0 mm | 5.96 mm | 104.35 mm | 1 | Black nitride stainless steel |
| SIVN-1012-8 | SUPERTECH | +0.5 mm | 36.5 mm | 5.96 mm | 104.35 mm | 1 | Black nitride stainless steel |
| SIVN-1012-2-8 | SUPERTECH | +0.5 mm | 36.5 mm | 5.96 mm | 103.85 mm | 1 | Black nitride stainless steel |
| SIVN-1014-8 | SUPERTECH | +1 mm | 37.0 mm | 5.96 mm | 104.35 mm | 1 | Black nitride stainless steel |
| SIVN-1014-2-8 | SUPERTECH | +1 mm | 37.0 mm | 5.96 mm | 103.85 mm | 1 | Black nitride stainless steel |
| F1520P*8 | FERREA | Standard | 36.0 mm | 5.97 mm | 104.60 mm | Stainless, chrome stem | |
| F1524P*8 | FERREA | +1 mm | 37.0 mm | 5.97 mm | 104.60 mm | Stainless, chrome stem | |
| F1967P*8 | FERREA | Standard | 36.0 mm | 5.97 mm | 104.44 mm | Stainless, chrome stem | |
| F1965P*8 | FERREA | +1 mm | 37.0 mm | 5.97 mm | 104.44 mm | Stainless, chrome stem | |
| F6077*8 | FERREA | Standard | 36.0 mm | 5.97 mm | 104.60 mm | EV8 stainless steel, hard chrome stem | |
| F6078*8 | FERREA | +1 mm | 37.0 mm | 5.97 mm | 104.60 mm | EV8 stainless steel, hard chrome stem |
SIVN-1012-2-8: length and groove 0.5 mm lower than standard; SIVN-1014-2-8: 0.5 mm shorter than standard.
SIVN-1014-8: 4.3 mm stem tip, as standard. FERREA valves: 3.5 mm stem tip.
F1520P*8 and F1524P*8: Impreza WRX STi 2004 to 2008; F1524P*8 is fitted with FERREA K10074 collets.
F1967P*8 and F1965P*8: Impreza WRX EJ20 2001 to 2008, 19° Super Flo profile; F1965P*8 is fitted with FERREA K10061 collets.
F6077*8 and F6078*8: Impreza WRX EJ20 2001 to 2008 and WRX STi 2004 to 2008; F6078*8 is fitted with FERREA K10061 collets.
Fitting details
| Part | SUBARU original | Reinforced |
|---|---|---|
| Collets | 13210AA020 | KPR-6T-ST / K10061 / K10074 |
| Valve stem seals | 13207AA050 / 13207AA120 | VS-TS6I-8 / VS1016 |
| Valve guide | 13212-AA130 | GDE-SUEJ6-I-8 / VG1073 |
The +0.5 mm and +1 mm sizes need inlet seats cut to 36.5 mm or 37 mm; at standard size the seats keep their diameter.
The SUPERTECH valves are fitted with 6 mm, 6° single groove collets, two per valve.
After replacing the valves, check the inlet clearance, 0.18 to 0.22 mm cold, and reset it if needed.
Technical guide
Our brands
| SUPERTECH Performance has been creating racing valvetrain parts in San Jose, California, for over thirty years. Each valve, designed for one engine only, goes through ultrasound, X-ray and laser checks, then is proven with engine builders, from drag strip to track. | |
| FERREA Racing Components was born in 1978 in Fort Lauderdale, Florida, founded by two engine builders from Argentina, with all production kept on site. Its one-piece valves, forged from bar and fully CNC machined, run in NASCAR, on circuits and on the drag strip. |
How to choose
The groove is the notch near the stem tip, where the collets hold the retainer. The SUPERTECH valves here have only one, so the choice is size and length.
| Criterion | Option 1 | Option 2 |
|---|---|---|
| Size | Standard size 36.0 mm head, the same as the Subaru valve, offered by SUPERTECH and FERREA alike. It suits a head whose inlet seats have not left factory size, and goes in without any machining. |
+0.5 mm or +1 mm 36.5 mm head (SUPERTECH only) or 37.0 mm: the larger passage at the seat lets more air in, about 10 to 12 cfm per mm of head, which benefits power. The inlet seats must be recut to that diameter, which also rescues a head whose seats were already reground. |
| Length | Standard length 104.35 mm at SUPERTECH, 104.44 or 104.6 mm at FERREA, for a 104.4 mm Subaru valve. The stem tip measures 4.3 mm, as standard, on the standard length SUPERTECH +1 mm, and 3.5 mm on the FERREA valves. |
0.5 mm shorter 103.85 mm, in +0.5 mm or +1 mm oversize, at SUPERTECH only. On the +0.5 mm version, the groove also sits 0.5 mm lower than standard. The collets remain 6 mm single groove parts, two per valve, preferably new. |
When reinforced valves become necessary
- Boost raised above factory setting
- More aggressive camshaft profile or harder springs
- Rev limiter moved upwards
- Cylinder head rebuilt for racing: rally, circuit or drift
- Damaged or worn original valves, or reground seats
Compatible vehicles
| Model | Engine code | Power | Years |
|---|---|---|---|
| Legacy I (BC, BF) 2.0 Turbo | EJ20-GN | 200 hp | 1992-1994 |
| Impreza (GC, GF) 2.0 Turbo, WRX, WRX STi | EJ20G | 211-275 hp | 1992-2000 |
| Impreza (GF) 2.0 WRX | EJ20U | 241 hp | 1993-2000 |
| Impreza (GC, GF, GD, GG) 2.0 Turbo, WRX | EJ205 | 204-250 hp | 1998-2007 |
| Forester (SF) 2.0 S Turbo | EJ205 | 170-177 hp | 1998-2002 |
| Forester (SG) 2.0 S Turbo, Cross Sports | EJ205 | 177-220 hp | 2002-2007 |
| Forester (SH) 2.0 | EJ205 | 230 hp | 2007-2012 |
| Impreza (GC, GF, GD, GG, GV) 2.0 WRX STi | EJ207 | 265-320 hp | 1996-2015 |
| WRX STi (VA, GJ) 2.0 | EJ207 | 308 hp | 2013- |
| Legacy IV (BL, BP) 2.0 Turbo, GT | EJ20X | 245-258 hp | 2003-2009 |
| Legacy IV (BL, BP) 2.0, 2.0 GT | EJ20Y | 179-272 hp | 2003-2015 |
| Impreza (GD, GG, GR, GV) 2.5 WRX | EJ255 | 230-272 hp | 2005- |
| Forester (SG) 2.5 Turbo | EJ255 | 230-256 hp | 2004-2009 |
| Forester (SH) 2.5 Turbo | EJ255 | 230-270 hp | 2008-2015 |
| Legacy IV (BL, BP), Outback (BP) 2.5 Turbo | EJ255 | 233-253 hp | 2004-2009 |
| Legacy V (BM, BR) 2.5 GT | EJ255 | 233-286 hp | 2009-2015 |
| WRX 2.5 | EJ255 | 233 hp | 2011- |
| Baja 2.5 | EJ255 | 233 hp | 2003-2006 |
| Legacy IV (BL, BP), Outback (BP) 2.5 T, STI | EJ25DET | 250-265 hp | 2006-2009 |
| Impreza (GD, GG, GR, GV) 2.5 WRX STi | EJ257 | 265-400 hp | 2005- |
| Forester (SG) 2.5 | EJ257 | 211 hp | 2003-2005 |
| WRX STi (GJ, GP, VA) 2.5 | EJ257 | 300-310 hp | 2010- |
OEM part number (inlet valve): 13201AA390 / 13201AA391 / 13201AA371 / 13201AA400 / 13201AA510
Don't forget the exhaust valves
A head rebuild calls for new valves on both the inlet and exhaust sides, plus fresh valve stem seals. The exhaust valves for these engines are here:
| Reinforced exhaust valves Subaru EJ20 EJ205 EJ207 EJ255 EJ257 → |
-
Brand
-
ReferenceF6077*8