Skip to content
  • On order
Crankshaft thrust washers VAG EA888 Gen 3 Crankshaft thrust washers VAG EA888 Gen 3 Crankshaft thrust washers VAG EA888 Gen 3 Crankshaft thrust washers VAG EA888 Gen 3

Crankshaft thrust washers VAG 1.8 TFSI EA888 Gen.3

€18.47 (tax incl.)
€20.52 (tax incl.) -10%

Crankshaft thrust washers for the VAG EA888 Gen 3 four-cylinder engine.

  • Brands: King
  • Fits: Audi A3, A4, A5, TT; Seat Leon; Skoda Octavia, Superb; Volkswagen Golf, Passat, Touran
  • Engine codes: CJEB, CJSA, CJSB, CJSC
TW1088AM
On order, 15 to 30 days lead time
Pay in installments

The VAG EA888 Gen 3 four-cylinder engine

The third-generation EA888 (Gen 3) is a turbocharged four-cylinder petrol engine from the VAG group (Volkswagen, Audi, Seat, Skoda). It powers the Audi A3 8V, A4 B8, A5 and TT, the Seat Leon, the Skoda Octavia III and Superb III, and the Volkswagen Golf Alltrack, Passat B8 and Touran, among others. Introduced in 2011, the third generation is an inline four-cylinder with a grey cast iron block, 16 valves, double overhead camshafts, a timing chain, direct injection and a turbocharger.

Thrust washers

Thrust washers take the clutch thrust and set the crankshaft end play. On a tuned engine with a reinforced clutch, this thrust increases. The King version, in lead-free Al20Sn1Cu aluminium, is certified by its manufacturer to meet or exceed the vehicle manufacturer's specifications.

Fitted on either side of a main bearing, the half washers hold the crankshaft in its axial position. They work every time the clutch is disengaged, when the clutch pushes the crankshaft against them. A worn washer lets the end float increase and the crankshaft shift, at the expense of its own thrust faces.

Technical specifications

Part numberBrand and treatmentSizeInner Ø (mm)Outer Ø (mm)Thickness (mm)Material
TW1088AM King - Uncoated Standard - - - Aluminium bi-metal Al20Sn1Cu
Manufacturer notes
King
TW1088AM: 1 pair, lead-free aluminium bi-metal
OE Replacement (AM) range, standard size only
Engine codes listed: CJEB, CJSA, CJSB, CJSC.

Technical guide

The lubrication grooves, present on one face of the half washer only, must face the crankshaft; the plain face rests against the block or cap. A reversed washer starves the crankshaft's thrust face of oil and damages it quickly.

Before fitting the cap, apply assembly grease to the crankshaft-side face and check that the half washers in the block are flush. The cap goes on without forcing and is then tightened according to the manufacturer's procedure. Finish by checking the end float with a dial gauge, to be compared with the manufacturer's value.

The brand

King Racing King Engine Bearings, an Israeli engine bearing manufacturer since the 1960s. Its OE Replacement (AM) range thrust washers are made of lead-free aluminium.

Construction and advantages

Criterion King
Presentation One-pair set
Country of manufacture Israel
Material Aluminium bi-metal Al20Sn1Cu, lead-free
Coating No
Available sizes Standard

Vehicle compatibility

These thrust washers fit the VAG EA888 Gen 3 four-cylinder engine (engine codes CJEB, CJSA, CJSB and CJSC) of the following vehicles:

BrandModel (chassis)Engine codePowerYears
Audi A3 (8V1, 8VK) CJSA, CJSB 180 hp 2012-2016
Audi A3 Convertible (8V7, 8VE) CJSA, CJSB 180 hp 2013-2017
Audi A3 Limousine (8VS, 8VM) CJSA, CJSB 180 hp 2013-2016
Audi A3 Sportback (8VA, 8VF) CJSA, CJSB 180 hp 2012-2016
Audi A4 B8 (8K2) CJEB 170 hp 2011-2015
Audi A4 B8 Avant (8K5) CJEB 170 hp 2011-2015
Audi A5 (8T3) CJEB 170 hp 2007-2017
Audi A5 Convertible (8F7) CJEB 170 hp 2011-2016
Audi A5 Sportback (8TA) CJEB 170 hp 2011-2017
Audi TT (FV3, FVP) CJSA, CJSB 180 hp 2015-2018
Audi TT Roadster (FV9, FVR) CJSA, CJSB 180 hp 2015-2018
Seat Leon (5F1) CJSA 180 hp 2013-2018
Seat Leon SC (5F5) CJSA 180 hp 2013-2018
Seat Leon ST (5F8) CJSA, CJSB 180 hp 2013-2018
Skoda Octavia III (5E3, NL3, NR3) CJSA, CJSB 180 hp 2012-2020
Skoda Octavia III Combi (5E5, 5E6) CJSA, CJSB 180 hp 2012-2020
Skoda Superb III (3V3) CJSA, CJSC 180 hp 2015-2024
Skoda Superb III Estate (3V5) CJSA, CJSC 180 hp 2015-2024
VW Golf Alltrack VII Variant (BA5, BV5) CJSB 180 hp 2014-2020
VW Passat B8 (3G2, CB2) CJSA, CJSC 180 hp 2015-2019
VW Passat B8 Variant (3G5, CB5) CJSA, CJSC 180 hp 2015-2019
VW Touran (5T1) CJSA 180 hp 2015-2018

Why replace the thrust washers

Half washers are inexpensive parts, but their wear is costly: excessive end float lets the crankshaft move at every disengagement and attacks its thrust faces, which then have to be machined, if the crankshaft does not need replacing. Changing them whenever the bottom end is opened, and always with an uprated clutch, avoids that expense.

14 other products in the same category

Viewed products

Loading...