Skip to content
  • On order
Reinforced head gasket Austin Sprite - C4145-043 Reinforced head gasket Austin Sprite - C4145-043

Reinforced head gasket Austin-Healey Sprite 9CG 10CC

€101.21 (tax incl.)
€134.95 (tax incl.) -25%

Reinforced Cometic head gasket, in copper. Sold individually, one gasket per engine.

  • Brand: Cometic
  • Engines: 9CG, 10CC
  • Bore: 67.5 mm
  • Thickness: 1.09 mm
  • Replaces: AJM302
C4145-043
0 in stock in France
On order, 15 to 30 days lead time
Pay in installments

The Austin engines covered

The petrol engines 9CG (0.9 litre) and 10CC (1.1 litre) power the Austin-Healey Sprite Mk I, Mk II and Mk III listed below.

This original gasket carries the part number AJM302. Its bore is 68 mm; the manufacturer publishes neither its construction nor its thickness. It is sized for standard combustion pressure: as that pressure rises, the clamping load relaxes, the cylinder head lifts and coolant gets into a cylinder.

Reinforced cylinder head gaskets

The head gasket does not make the seal on its own: it holds because the fasteners press the cylinder head against the block. Copper that is 99.9% pure brings good corrosion resistance, high ductility and high thermal conductivity, without becoming brittle under heat.

This page offers the part number from Cometic, an American maker of racing gaskets, in a single construction: copper. Its bore is 67.5 mm, against 68 mm for the original gasket, and its thickness is 1.09 mm. As a general rule, a gasket bore at least 0.5 mm larger than the actual cylinder bore is chosen. The part number is sold individually, one gasket per engine.

Technical specifications

Gasket bore
OEM 68 mm
Thickness Gasket volume Gasket type
OEM not specified
Brand Part number
OEM AJM302
67.5 mm 1.09 mm 3.90 Copper Cometic C4145-043

Gasket volume is the space the gasket leaves free above each cylinder. Added to the combustion chamber, it lowers the compression ratio, the more so as it grows. Values can only be compared at the same gasket bore.

Preparation and fitting

Fasteners Engines Tightening torque
Original cylinder head bolts 9CG, 10CC not published by the manufacturer

Before fitting, check the flatness of the cylinder head and block with a straight edge and have them resurfaced if necessary. Cometic precision-tests the flatness of its copper gaskets.

Technical guide

The construction offered

Cometic copper
A sheet of oxygen-free C110 copper, 99.9% pure. The metal resists corrosion well, deforms without breaking, conducts heat well and does not become brittle under heat. Cometic precision-tests the flatness of each gasket and recommends, for optimal results, fitting it with a crimped sealing ring.

Choosing bore and thickness

Gasket bore. The Cometic copper gasket is offered in 67.5 mm (C4145), in that bore only.

Thickness. The manufacturer does not state the thickness of the original gasket. A thicker gasket enlarges the combustion chamber and lowers the compression ratio; a thinner one reduces it and raises the ratio.

Your goal Thickness to choose
Keep the original compression ratio Original thickness not published by the manufacturer: measure the one on the removed gasket and set it against the only gasket offered, 1.09 mm
Skimmed cylinder head, make up the lost height Only one thickness is offered, 1.09 mm: set it against the removed gasket plus the material taken off
Forced induction build, lower the ratio 1.09 mm, if the thickness measured on the original gasket at removal is smaller
Naturally aspirated build, raise the ratio 1.09 mm, if the thickness measured on the original gasket at removal is greater

As the original thickness is not published, use a dial gauge to measure how far the pistons stand proud of the block, especially if the removed gasket is thicker than 1.09 mm: that figure sets the clearance left between piston and head.

The brand

Cometic Cometic Gasket, Inc. is an American maker of gaskets and engine sealing solutions, created in 1989 in Concord, Ohio. It became known for the made-to-order gasket, cut to the bore and thickness requested. Its whole production stays in the United States, using American raw materials.

Advantages over the original gasket

Criterion Original gasket AJM302 Reinforced gaskets
Construction Construction not stated by the manufacturer Pure copper, 99.9% (C110 grade)
Gasket bore 68 mm 67.5 mm
Thicknesses available thickness not published by the manufacturer 1.09 mm
Compression ratio adjustment None Through the thickness chosen
Resistance to overpressure Limited to standard output Designed for forced induction

When a reinforced gasket becomes necessary

  • Adding forced induction, or raising boost on an already turbocharged engine
  • Cylinder rebored beyond what the 68 mm bore of the original gasket covers
  • Looking for a compression ratio different from standard, higher or lower
  • Engine that has already lost its gasket, or is consuming coolant
  • Competition use, where the gasket goes through repeated temperature rises

Vehicle compatibility

Model Engine code Power Years
Austin-Healey Sprite Mk I 0.9 9CG 46 hp 1960-1963
Austin-Healey Sprite Mk II 0.9 9CG 46 hp 1961-1964
Austin-Healey Sprite Mk II 1.1 10CC 57 hp 1962-1964
Austin-Healey Sprite Mk III 1.1 10CC 56 hp 1964-1966

OEM part number: AJM302.

Important: the part number on this page fits only the 9CG and 10CC engines: check your vehicle's engine code before ordering.

Why switch to a reinforced gasket?

The copper gasket is designed to hold where the original gasket reaches its limit: pure copper is ductile and does not turn brittle under heat, which keeps the seal between cylinder head and block.

As soon as a turbo or supercharger is added, or the compression ratio is raised, the head gasket becomes the weak link of the top end. Choosing a reinforced gasket is then a matter of safety more than comfort: it avoids a failure and the cylinder head removal that goes with it.

16 other products in the same category

Viewed products

Loading...