Skip to content
  • On order
Reinforced head gasket Fiat Lancia 1.6 2.0 8v - 338412R Reinforced head gasket Fiat Lancia 1.6 2.0 8v - 338412R

Reinforced head gasket Fiat Lancia 1.6 2.0 8v 131C3 132C2 132D 138AR 828B 831A4

€88.98 (tax incl.)
€118.65 (tax incl.) -25%

Athena MLS reinforced gasket, sold individually: one gasket per engine.

  • Brand: Athena
  • Engines: 131C3, 132C2, 132D, 138AR, 828B, 831A4 and others
  • Bore: 85.5 mm
  • Thickness: 1.30 mm
  • Replaces: 4314165 and others
338412R
0 in stock in France
ORDER TODAY, WE SHIP IN 3 WEEKS
Pay in installments

The Fiat and Lancia engines covered

The petrol engines 124B21, 131C3, 132B1, 132C6, 132D, 138AR, 828B, 831A4, 132A, 131C4, 132C2, 132D1, 828B1 and 828B4, eight-valve four-cylinders of 1.6, 1.8 and 2.0 litres, power the Fiat 124 Coupe, 131, 132, Argenta, Ritmo and Regata, the Seat 132 and the Lancia Beta, Trevi and Delta I.

The original part numbers on record are 4314165, 4341243, 4387624, 4387625, 4434866 and 4435023, among others. The manufacturer publishes neither their bore, nor their construction, nor their thickness.

Reinforced cylinder head gaskets

Sealing is not down to the gasket alone: the fasteners that clamp the head onto the block contribute just as much. A composite gasket gives up for good beyond 100 N/mm², whereas the 301 stainless steel of an MLS gasket holds 517 N/mm² and regains its shape after every combustion. On an older engine, replace the bolts or studs as the workshop manual advises.

This page presents the part number from Athena, an Italian maker of racing gaskets, in one construction only: the MLS, a multilayer stainless steel gasket. Its bore is 85.5 mm and its thickness 1.30 mm. As a rule, the gasket bore must exceed that of the cylinders by at least 0.5 mm. It is sold individually: a single gasket fits one engine.

Technical specifications

Gasket bore Thickness Gasket volume Gasket type
OEM not specified
Brand Part number
OEM 4314165
85.5 mm 1.30 mm 7.46 MLS Athena 338412R

A gasket's volume is the space it leaves free above each cylinder. That space joins the combustion chamber and lowers the compression ratio; only gaskets of the same bore can be compared. Here, the bore offered is 85.5 mm.

Preparation and fitting

Fasteners Engines Tightening torque
Original cylinder head bolts 124B21, 131C3.000, 132B1.000, 132C6.000, 132D.000, 138AR.000, 828B.000, 831A4.000, 132A000, 131C4.000, 132C2.000, 132D1.000, 828B1.000, 828B4.000 not published by the manufacturer

Before fitting, check the flatness of the head and block with a straight edge and have them resurfaced if needed. Athena supplies this gasket ready to fit: apply no sealing paste. On an older block, this check is repeated at every rebuild.

Technical guide

The construction offered

Athena MLS cylinder head gasket Athena MLS
Several layers of AISI 301 stainless steel, laser cut, stamped and then riveted together. Around each cylinder, a layer folded over on itself, the Gas Stopper, concentrates the clamping load on the combustion chamber, while beads block the water and oil passages. The outer layers carry a two-coat finish: the first withstands high temperatures and fills small irregularities of the block and head, the second, silicone based, keeps the gasket from sticking at removal. It is Athena's all-steel answer, from the tuned naturally aspirated engine to moderate forced induction. Here, the MLS is offered in 85.5 mm and 1.30 mm.

Choosing bore and thickness

Gasket bore. The Athena MLS exists in 85.5 mm (338412R), with no other bore.

Thickness. The manufacturer supplies no thickness for the original gasket. For these engines, no value is released. A thicker gasket enlarges the combustion chamber and lowers the compression ratio; a thinner one reduces it and raises the ratio.

Your goal Thickness to choose
Keep the original compression ratio Original thickness not published: measure that of the removed gasket and set it against the only gasket available, 1.30 mm
Skimmed cylinder head, make up the lost height Only one thickness exists, 1.30 mm: set it against that of the removed gasket, plus the material taken off in resurfacing
Forced induction build, lower the ratio 1.30 mm, when the thickness measured on the original gasket at removal is lower
Naturally aspirated build, raise the ratio 1.30 mm, when the thickness measured on the original gasket at removal is higher

With no known original thickness, use a dial gauge to read how far the pistons rise above the block face, especially if the removed gasket is thicker than 1.30 mm: that figure gives the clearance left between piston and head. On these engines, the measurement is made with a dial gauge, head removed.

The brand

Athena Athena S.p.A. is an Italian maker of gaskets and engine components, established in Alonte, in Veneto, where its head office and main plant stand. It also has sites in Spain, the United States, Brazil and India. Several carmakers fit its multilayer gaskets on the assembly line, and its entire racing range is designed and built in Italy. Part number 338412R is the one on this page.

Advantages over the original gasket

Criterion Original gaskets 4314165, 4341243, 4387624, 4387625, 4434866 and 4435023, among others Reinforced gaskets
Construction Construction not stated by the manufacturer Multilayer stainless steel (MLS)
Gasket bore not published by the manufacturer 85.5 mm
Thicknesses available thickness not published by the manufacturer 1.30 mm
Compression ratio adjustment None By gasket thickness (1.30 mm)
Resistance to overpressure Limited to standard output Designed for forced induction

When a reinforced gasket becomes necessary

  • Adding forced induction, or raising boost on an already turbocharged engine
  • Cylinder rebored beyond what the 85.5 mm bore of the gasket offered covers
  • Looking for a compression ratio different from standard, higher or lower
  • Engine that has already lost its gasket, or is consuming coolant
  • Competition use, where the gasket goes through repeated temperature rises

Vehicle compatibility

Brand Model Engine code Power Years
Fiat 124 Coupé 1800 Sport 124B21 not published 1973-1976
Fiat 131 1.6 Super 131C3.000 97 hp 1978-1984
Fiat 131 Familiare / Panorama 1.6 Super 131C3.000 97 hp 1979-1981
Fiat 131 2.0 Super 131C4.000 113 hp 1981-1984
Fiat 132 1.8 132B1.000 107 hp 1974-1976
Fiat 132 1.6 132C6.000 not published 1977-1981
Fiat 132 2.0 132C2.000 112 hp 1976-1981
Seat 132 1.8 132A000 not published 1973-1980
Fiat Argenta 1600 132D.000 98 hp 1981-1985
Fiat Argenta 1600 i.e. 132D.000 90 hp 1981-1985
Fiat Argenta 2000 132D1.000, 132C2.000 113 hp 1978-1985
Fiat Ritmo 1.6 138AR.000 90 and 105 hp 1981-1987
Fiat Regata 100 1.6 and Weekend 138AR.000 105 hp 1983-1986
Lancia Beta 1600 (berline, coupé) 828B.000 not published 1976-1986
Lancia Beta 2000 (berline, coupé, HPE, Spider) 828B1.000, 828B4.000 not published 1976-1986
Lancia Trevi 1600 and 2000 i.e. 828B.000, 828B4.000 not published 1980-1987
Lancia Delta I 1.6 GT 831A4.000 not published 1982-1986

OEM part number: 4314165, 4341243, 4387624, 4387625, 4434866 and 4435023, among others.

Important: the part numbers on this page suit the 124B21, 131C3, 132B1, 132C6, 132D, 138AR, 828B, 831A4, 132A, 131C4, 132C2, 132D1, 828B1 and 828B4 engines: check your vehicle's engine code before ordering.

Why switch to a reinforced gasket?

When the original gasket is no longer enough, the reinforced gasket takes over: under higher combustion pressure it keeps its shape instead of being crushed. These Fiat and Lancia engines find here a gasket with an 85.5 mm bore.

Turbo, supercharger or a raised compression ratio: the head gasket is the first part stressed, the weak point of the top end. A reinforced gasket prevents the leak, and the head removal that goes with it costs well above the gasket. This holds for Fiat and Lancia engines as for any hard-driven engine.

16 other products in the same category

Loading...