Skip to content
  • In stock
Tri-metal crankshaft main bearings ACL Fiat Lancia Alfa Romeo 2.0 Tri-metal crankshaft main bearings ACL Fiat Lancia Alfa Romeo 2.0 Tri-metal crankshaft main bearings ACL Fiat Lancia Alfa Romeo 2.0 Tri-metal crankshaft main bearings ACL Fiat Lancia Alfa Romeo 2.0 Tri-metal crankshaft main bearings ACL Fiat Lancia Alfa Romeo 2.0 Tri-metal crankshaft main bearings ACL Fiat Lancia Alfa Romeo 2.0

Tri-metal crankshaft main bearings ACL Fiat Lancia Alfa Romeo 2.0

€169.30 (tax incl.)
€188.11 (tax incl.) -10%

Set of 10 tri-metal crankshaft main bearing half shells for Fiat, Lancia and Alfa Romeo engines (Ø 53 mm).

  • Brand: ACL Race
  • Fitments: Fiat Croma, Tipo, Coupé, Lancia Delta Integrale, Thema, Dedra, Alfa Romeo 155
  • Engine codes: 154, 160, 175, 831, 834, 835, 836, AR 67203
  • Available sizes: standard to +0.25 mm, increased clearance version (HX)
5M2908H-STD
48 in stock in Europe (72h lead time)
Available in stock in Europe (72h lead time)
Pay in installments

The Fiat, Lancia and Alfa Romeo 1.6 to 2.0 litre engines

This main bearing set fits a family of four-cylinder petrol engines from 1.6 to 2.0 litres, naturally aspirated and turbocharged, fitted notably to the Fiat Croma, Tempra, Tipo and Coupé, the Lancia Delta (including the HF Integrale), Thema, Dedra and Kappa, and the Alfa Romeo 155 and 164. All the applications listed below share the same crankshaft journal and housing dimensions: a single bearing set covers these engines.

The crankshaft of these engines runs on five main bearings. Each journal turns between two half shells, one seated in the block and the other in the main bearing cap: they carry the crankshaft. The ACL Race Series tri-metal set shown here replaces them on built engines.

Tri-metal main bearings

A trimetal bearing combines three layers with complementary roles: a steel back that provides structural strength, a copper-lead intermediate layer that takes the heavy loads and an anti-friction running layer that protects the main journal. The complete set contains 0 half shells, i.e. The complete set covers the five main bearings of the crankshaft. The upper and lower half shells are identical.

An aluminium bi-metal bearing, intended for low to medium loads, tops out at around 8,000 psi; a performance trimetal bearing holds up to 12,000 psi, 50% more load capacity. It therefore gains strength and service life on turbocharged, supercharged or high-revving engines.

Technical specifications

Fitment dimensions common to all references
ACL bearings
Crankshaft journal Ø 52.991 / 53.000 mm
Housing bore Ø 56.717 / 56.735 mm
Width 20.75 mm
ReferenceBrand and treatmentSizeWall thickness (mm)
5M2908H-STD ACL Race - Untreated Standard 1.843
5M2908HX-STD ACL Race - Untreated Std, increased clearance (HX) 1.830
5M2908H-.025 ACL Race - Untreated +0.025
5M2908H-.25 ACL Race - Untreated +0.25

Running clearance

Running clearance is the space left between the bearing and the main journal, permanently filled by the oil film.

With the engine running, the main journal does not touch the bearing: it rides on this oil film, which takes the load. The clearance sets the film thickness. Too small, it restricts oil flow, raises the temperature and invites seizure; too large, it lets the oil escape, the film loses its load capacity and oil pressure falls. The right clearance combines sufficient lubrication with an oil film that keeps carrying the load.

Size / gradeWhen to choose itACL Race Series
Standard (STD) Standard journal, not reground 0.055 to 0.066 mm
Increased clearance (HX) Wider clearance: high oil flow, high rpm 0.081 to 0.091 mm
+0.025 mm Polished journal 0.055 to 0.066 mm
+0.25 mm Journal reground to 0.25 mm 0.055 to 0.066 mm

Checking on assembly: lay a calibrated strip (Plastigauge) on the journal, torque the main cap to spec, then compare the crushed strip against the gauge to read the clearance.

Plastigauge

Order the Plastigauge →

Technical guide

The ACL main bearings shown here are trimetal bearings built for engine tuning and racing. They withstand far higher loads than a standard bearing and come in several sizes: the standard size, a +0.025 mm size for a main journal that has only been polished, a +0.25 mm regrind size and the HX version with increased clearance for high-revving engines or engines needing a high oil flow. This range lets you refit a reground crankshaft without changing product line and match the clearance to the oil and use chosen.

The brand

ACL Bearing Company Founded in Australia in 1949, ACL Bearing Company designs high-performance engine bearings. Its Race Series brings together precision trimetal bearings, offered in a wide choice of sizes and fitted to built engines around the world.

Vehicle compatibility

This main bearing set fits the following vehicles, by engine code:

BrandModel (chassis)Engine codePowerYears
Alfa Romeo 155 (167_) AR 67203 186–190 hp 1992–1997
Alfa Romeo 164 (164_) AR 06476 174–175 hp 1987–1998
Fiat Coupe (175_) 175 A1.000, 836 A3.000 139–190 hp 1993–1996
Fiat Croma (154_) 154 A1.000, 154 A2.000, 154 C4.046, 154 C5.000, 154 E1.000, 834 C.146 90–155 hp 1985–1996
Fiat Tempra (159_) 154 C4.000, 154 E1.000, 836 A4.000 69–165 hp 1990–1998
Fiat Tempra S.w. (159_) 836 A4.000 69 hp 1992–1996
Fiat Tipo (160_) 160 A5.000, 160 A8.046, 836 A3.000, 836 A4.000 70–146 hp 1989–1995
Lancia Dedra (835_) 835 A5.046, 835 A7.000, 835 A7.046, 835 A8.000, 835 A8.046, 836 A3.000 113–177 hp 1989–1999
Lancia Dedra SW (835_) 836 A3.000 139 hp 1994–1999
Lancia Delta I (831_) 831 A7.000, 831 B3.000, 831 B5.000, 831 B7.046, 831 C5.000, 831 C5.046, 831 D5.000, 831 E5.000, 831 E5.046 131–215 hp 1983–1994
Lancia Delta II (836_) 175 A4.000, 836 A2.000, 836 A3.000, 836 A4.000 69–193 hp 1993–1999
Lancia Thema (834_) 834 C.000, 834 C.146, 834 C1.000, 834 C1.246, 834 F1.000, 834 F2.000 150–201 hp 1984–1994
Lancia Thema SW (834_) 834 C.000, 834 C.146, 834 C1.000, 834 C1.246, 834 F1.000, 834 F2.000 150–201 hp 1987–1994

Why replace the bearings

A failing main bearing does not fail alone: it scores the main journal, sends debris through the oil circuit and calls at least for a crankshaft regrind, when it does not damage the block as well. On a built engine, a bearing set costs only a fraction of a regrind, and even less of a full rebuild: it is the cheapest part of the crankshaft assembly and the one whose failure costs the most.

12 other products in the same category

Viewed products

Loading...