Skip to content
  • In stock
Kits coupelle renforcé TU5J4 Kits coupelle renforcé TU5J4

Reinforced valve spring kit BMW M30B35

€414.72 (tax incl.)
€518.40 (tax incl.) -20%

Kit of 12 reinforced double valve springs with 12 upper retainers for the BMW 3.5 L 12V M30B35 straight-six.

  • Brands: CATCAMS
  • Engine: M30B35 (3.5 L 12V)
  • Springs: double
  • Contents: springs and upper retainers
PAC-D95009*12+99326/H*12
1 in stock in France
Pay in installments

The BMW 3.5 L 12V M30B35 straight-six

The M30B35 is the BMW 3.5-litre, 12-valve straight-six fitted to the 635CSi, 535i and 735i as well as the Rayton Fissore Magnum 3.5. A single overhead camshaft opens all twelve valves through rocker arms, and each valve carries a double spring.

As built, each valve has a double spring, an upper retainer, a spring seat and three-groove collets, under a rocker arm. The kit replaces the springs and upper retainers: the original spring seats and collets stay in place.

CATCAMS reinforced valve spring kit

A valve spring pushes the valve home on its seat and presses the rocker arm against the cam, cycle after cycle. As revs climb the moving mass becomes harder to control, and a weak spring allows float, even contact with the piston.

Included in this CATCAMS kit are 12 PAC-D95009 double springs and 12 upper retainers 99326/H, one set for each M30B35 valve. A double spring pairs an outer PAC-E95009 spring with an inner PAC-I95009 spring nested inside it.

Valve spring kit technical specification

Part numberBrandSpringsOuter / inner ØSeat pressureOpen pressureRateMax liftKit contents
PAC-D95009*12+99326/H*12 CATCAMS Double Outer 30.7 / 23.2 mm 12 double springs, 12 retainers

Valve spring kit fitting details

PartBMW originalReinforced spring kit
Spring 11 34 1 714 768 + 11 34 1 714 767 Kit specific: PAC-D95009 (CATCAMS)
Retainer 11 34 1 713 412 Kit specific: 99326/H (CATCAMS)
Spring seat 11 34 1 713 413 Original kept
Collets 11 34 1 710 975 Original kept

The kit contains 12 PAC-D95009 double springs, each made of a PAC-E95009 outer spring and a PAC-I95009 inner spring, plus 12 upper retainers 99326/H. The original spring seats and collets are kept. The outer spring measures 43.6 mm free and 17.7 mm at coil bind, the inner spring 39.2 mm and 15.4 mm.

Load curve of the outer spring PAC-E95009 :
Load curve of the outer spring PAC-E95009

Load curve of the inner spring PAC-I95009 :
Load curve of the inner spring PAC-I95009

Between the bottom spring seat and the retainer on top, with the valve shut, you read the installed height. Every load figure belongs to one specific height and means nothing at another. Machining the valve seats pushes the parts further apart; for every millimetre gained, the load drops by the rate figure in newtons. After machining, measure all 12 valves.

CATCAMS
Installed height
Seat pressure at this height

Technical guide

Our brands

CATCAMS Cat Cams N.V. sells its camshafts for competition under the CATCAMS name, from its base in Belgium to customers abroad. A computer-controlled grinder lets it profile even angled lobes, and the brand's valve springs target shafts built for BTCC cars and for the Le Mans 24 Hours.

How to choose

A firmer spring helps the valve track the cam profile at high revs, so a hotter camshaft, a raised limiter or a turbo can be considered without float. CATCAMS publishes a load-versus-height curve for every spring, reproduced above; take your own installed height and read the load there.

CriterionKey point
Choosing the pressure The installed height you end up with on your head sets the seat pressure. Read it on the curves of the outer and inner springs; their forces add up because they act together. Balance cam profile, target revs and any turbo, but never ask for more force than the job needs, since surplus load simply wears cams and rocker arms. CATCAMS lists no load for the stock springs; a percentage gain is therefore left unquoted. Re-check the height after any further work on the head.
Single or double spring The production engine already runs a double spring on each valve, and this kit keeps that layout with PAC-E95009 outside and PAC-I95009 inside. Nothing else about the valve train changes: just springs and upper retainers are swapped.

When reinforced springs become necessary

  • A camshaft sharper than stock
  • A rev limit lifted by the build
  • A turbo fitted to the straight-six
  • A head reworked for circuit or special-stage racing
  • Weak springs, or valves floating well before the red zone

Compatible vehicles

ModelEngine codePowerYears
BMW 635CSi (E24) M30B35 211-218 hp 1988-1989
BMW 535i, M535i (E28) M30B35 218 hp 1985-1987
BMW 735i (E32) M30B35 211 hp 1989-1992
BMW 535i (E34) M30B35 211-218 hp 1988-1993
Rayton Fissore Magnum 3.5 M30B35 1988-1989

OEM reference (valve spring): 11 34 1 714 768 (outer spring) and 11 34 1 714 767 (inner spring).

Important: this kit is intended for the 3.5 L 12V M30B35 straight-six. For any other BMW engine, check the engine code before ordering.

Related products

With the head already stripped, also check the guides and the valves themselves, inlet as well as exhaust, as they will have to cope with firmer springs.

16 other products in the same category

Viewed products

Loading...