Skip to content
  • On order
Reinforced inlet valves Audi R8 Lamborghini V10 Reinforced inlet valves Audi R8 Lamborghini V10

Reinforced inlet valves AUDI R8 LAMBORGHINI Gallardo Huracán V10 5.0 5.2

€603.19 (tax incl.)
€753.98 (tax incl.) -20%

Set of 20 reinforced inlet valves for AUDI R8 V10 and LAMBORGHINI Gallardo, Huracán.

  • Brands: FERREA, SUPERTECH
  • Engines: V10 5.0 and 5.2 (BUJ, CTYA, CMPA, CTPA, CTPB, CSPA, CSPB, DKAA, DKAB, CEH, CSJB, DKB, DKBA)
  • Dimensions: 33.85, 33.9 or 34.85 mm head, 5.98 mm stem
  • Material: stainless steel with hard chrome stem, black nitrided stainless steel, single or 3 grooves
VWIVN-1002S-20
0 in stock in France
ORDER TODAY, WE SHIP IN 5 - 15 DAYS
Pay in installments

AUDI and LAMBORGHINI engines covered

The naturally aspirated 40-valve V10 shared by Audi and Lamborghini first appeared as a 5-litre unit in the 2003 Gallardo (codes L 510 and L510R). Enlarged to 5.2 litres, it then powered both generations of the Audi R8 V10, coupé and Spyder, from 525 to 610 hp depending on the engine code (BUJ, CTYA, CMPA, CTPA, CTPB, CSPA, CSPB, DKAA, DKAB), followed by the Gallardo 5.2 (CEH, CMPA) and the Huracán (CSJB, DKB, DKBA).

Each engine carries 20 inlet valves, two per cylinder. A high factory rev ceiling, more aggressive camshafts or added forced induction load them harder every time they open and land back on their seats.

FERREA and SUPERTECH reinforced inlet valves

In a V10 that revs this high, every valve on the inlet side lets fresh air into the cylinder and then shuts thousands of times every minute. As it closes, the head hammers onto its seat in the head casting, and its stem never stops rubbing against the guide that centres it. It has to cope with 400 to 550 °C. At those temperatures the chrome-silicon of ordinary valves drops back sharply: 500 MPa at 500 °C, only 250 MPa at 600 °C, barely hotter, meaning 50 % of its strength is gone. Extra lift, stiffer springs or higher revs make shocks, heat and wear even worse.

Both chosen makers use a chrome-nickel stainless steel related to EV8 (21-4N), holding 650 MPa at 500 °C, 30 % more than chrome-silicon, and 550 MPa at 600 °C, 120 % more. The FERREA comes from the Competition Plus series, for which its maker claims 20 % more strength when hot and under fatigue loading, plus a seat life extended by 25 %; its stem is hard chromed. The SUPERTECH valves go through black nitriding, a treatment that hardens and smooths the surface to spare the stem as it works in the guide.

The SUPERTECH +1 mm oversize set takes the head from 33.85 to 34.85 mm, leaving the 5.98 mm stem and the 103.9 mm length unchanged. The wider seat lets more air in, each cylinder fills better and power rises, as long as the 20 inlet seats are cut to this diameter.

Inlet valve technical specification

Part numberBrandSizeHead ØStem ØLengthGroovesMaterial
F2286P*20 FERREA Standard 33.9 mm 5.98 mm 104.0 mm 3 Stainless steel, hard chrome stem
VWIVN-1002S-20 SUPERTECH Standard 33.85 mm 5.98 mm 103.9 mm 1 Black nitrided stainless steel
VWIVN-1004S-20 SUPERTECH +1 mm 34.85 mm 5.98 mm 103.9 mm 1 Black nitrided stainless steel

F2286P*20: Lamborghini Gallardo 5.0 and Huracán. VWIVN-1002S-20 and VWIVN-1004S-20: Audi R8 V10, Lamborghini Gallardo 5.2 and Huracán.

Fitting details

PartAUDI / LAMBORGHINI originalReinforced
Collets KPR-6S-7-20*2 (single groove)
Valve stem seals VS-VBM6I-20 (inlet)
Valve guide

Every valve needs collets drawn for its grooves: SUPERTECH specifies KPR-6S-7 for its single groove valves, while the 3-groove FERREA valves go in with 3-groove collets.

With the 34.85 mm head, the 20 inlet seats must be recut to that size by a cylinder head workshop before reassembly.

Technical guide

Our brands

FERREA FERREA Racing Components started in 1978 in Fort Lauderdale, Florida, the work of two engine specialists from Argentina, and keeps all production in house. Its one-piece valves, forged and then CNC machined, are found in NASCAR as well as on race tracks and drag strips.
SUPERTECH Founded in Silicon Valley, SUPERTECH has, for three decades and more, engineered racing valves, valve springs and retainers. Each design targets one engine, is inspected through ultrasonic testing, radiography and laser, then approved by drag and track tuners.

How to choose

Below the retainer, two collets pinch the groove near the stem tip and lock the valve. The groove count decides how it is held, and its limits.

CriterionOption 1Option 2
Size Standard size
33.9 mm head (FERREA) or 33.85 mm (SUPERTECH), for inlet seats that have never been recut.
+1 mm oversize
34.85 mm head: larger seat, better-filled cylinders, more power (around 10 to 12 cfm per extra mm of head). Seat recutting to this size is required, a fix that also saves seats worn by regrinding.
Grooves 3 grooves
Close to the factory set-up, stem free to rotate, suited to a road V10 with few changes; new collets advised. Limit: at very high rpm, impacts load the bottom groove, where the stem is thinnest. FERREA version, Gallardo 5.0 and Huracán.
Single groove
Held between its collets, the stem frees the groove from almost all the effort, and a bigger contact surface cuts friction. Holds firm under harder springs, large lift and high engine speed. SUPERTECH versions, KPR-6S-7 collets required, ideally new.

When reinforced valves become necessary

  • Taller cam profiles, harder valve springs
  • Rev limiter pushed further up
  • V10 converted with a supercharger or twin turbos
  • Heads reworked for circuit, drift or rally use
  • Factory valves marked, tired or already reground

Compatible vehicles

ModelEngine codePowerYears
Audi R8 (422, 423) 5.2 FSI quattro BUJ / CTYA 525 hp 2009-2015
Audi R8 (422, 423) 5.2 FSI quattro CMPA 560 hp 2010-2015
Audi R8 (422, 423) 5.2 FSI quattro CTPA 550 hp 2012-2015
Audi R8 (422, 423) 5.2 FSI quattro CTPB 570 hp 2014-2015
Audi R8 Spyder (427, 429) 5.2 FSI quattro BUJ / CTYA 525 hp 2010-2015
Audi R8 Spyder (427, 429) 5.2 FSI quattro CMPA 560 hp 2011-2015
Audi R8 Spyder (427, 429) 5.2 FSI CTPA 550 hp 2012-2015
Audi R8 Spyder (427, 429) 5.2 FSI CTPB 570 hp 2012-2015
Audi R8 (4S3, 4SP) 5.2 FSI quattro CSPB / DKAB 540 hp 2015-
Audi R8 (4S3, 4SP) 5.2 FSI Plus quattro CSPA / DKAA 610 hp 2015-
Audi R8 (4S3, 4SP) 5.2 FSI RWS DKAB 540 hp 2017-
Audi R8 Spyder (4S9, 4SR) 5.2 FSI quattro CSPB / DKAB 540 hp 2016-2021
Audi R8 Spyder (4S9, 4SR) 5.2 FSI quattro CSPA / DKAA 610 hp 2017-
Audi R8 Spyder (4S9, 4SR) 5.2 FSI RWS DKAB 540 hp 2017-
Lamborghini Gallardo 5.0, Superleggera L 510 / L510R 500-530 hp 2003-2009
Lamborghini Gallardo Spyder 5.0 L510R 520 hp 2005
Lamborghini Gallardo 5.2, 5.2 AWD, LP 550-2, LP 560-2, LP 560-4 CEH / CMPA 551-578 hp 2008-2014
Lamborghini Gallardo Spyder 5.2, 5.2 AWD, LP 560-4 CEH / CMPA 551-578 hp 2008-2013
Lamborghini Huracán LP 580-2, LP 600-4, LP 610-4 CSJB / DKB / DKBA 580-610 hp 2014-2019
Lamborghini Huracán Spyder LP 580-2, LP 610-4 CSJB / DKB 579-610 hp 2015-2016
Important: one set of 20 covers a complete engine, two inlet valves per cylinder. The SUPERTECH valves suit the Audi R8 V10, the Gallardo 5.2 and the Huracán; the FERREA F2286P*20 suits the Gallardo 5.0 and the Huracán. The Huracán Performante, LP 610-2 and LP 640-2 are not covered.

Don't forget the exhaust valves

While the V10 heads are off, use the opportunity to fit 20 reinforced exhaust valves as well, plus fresh inlet valve stem seals for these V10 units:

AUDI R8 LAMBORGHINI Gallardo V10 5.0 5.2 exhaust valves →
AUDI R8 V10 5.2 inlet valve stem seals →

10 other products in the same category

Loading...