- On order
Reinforced exhaust valves Honda Civic CRX D15B D16A6
Set of 8 reinforced exhaust valves for Honda D15B and D16A6.
- Brands: SUPERTECH, FERREA
- Engines: D15B, D16A6 (Civic IV and V, CRX II and III)
- Dimensions: 25 mm head (standard) or 26 mm, 5.5 mm stem
- Material: black nitrided stainless steel or Super Alloy
Honda engines covered
The 1.5 litre D15B and the 1.6 litre D16A6 are Honda single camshaft, 16 valve four-cylinder engines. They power the Civic IV and V and the CRX II and III from the late 1980s to the mid 1990s.
They have 8 exhaust valves. On the D15B, the original part 14721-PM3-000 has a 5.5 mm stem and a 118.7 mm length, with a 24.9 to 25.1 mm head; it is held by the 14781-PJ7-003 collets.
SUPERTECH and FERREA reinforced exhaust valves
On a D15B or D16A6, the exhaust valve is the only one bathed in the gases leaving the chamber, hence far more heat than on the inlet side. Its head temperature, read in the metal, ranges from 760 to 870 °C unboosted and passes 1,000 °C when a turbo is grafted on. Around 75 % of this heat goes into the seat and close to 20 % into the guide. Taken as the yardstick for the original part, the EV8 steel family keeps 550 MPa at 600 °C yet offers only 300 MPa at 800 °C. Any tuning that raises torque, revs or boost heats the head further: it tires, warps and the seat no longer closes.
To withstand those temperatures, the reinforced versions change material and treatment. The SUPERTECH HEVN-1003 is in black nitride stainless steel: nitriding builds a hard, smooth surface layer that rubs less in the guide and wears the stem less, while keeping the original dimensions. The FERREA F1857P and F1858P belong to the Competition Plus range and are cut from Super Alloy, a nickel-rich superalloy; the maker credits this range with 20 % higher hot strength and seat life up by 25 %. Two finishes are therefore available: SUPERTECH black nitride stainless, valid for the D15B as for the D16A6, and FERREA Super Alloy, kept for the D16A6.
There is also a head widened by 1 mm: the F1858P goes from 25 to 26 mm, with stem and length unchanged. The cylinder empties its burnt gases sooner and takes in fresh charge better, which serves output. The exhaust seats must be machined to 26 mm.
Exhaust valve technical specifications
| Part number | Brand | Size | Head Ø | Stem Ø OEM 5.5 mm | Length OEM 118.7 mm | Grooves | Material |
|---|---|---|---|---|---|---|---|
| HEVN-1003-8 | SUPERTECH | Standard | 25 mm | 5,5 mm | 118.8 mm | 1 | Black nitrided stainless steel |
| F1857P*8 | FERREA | Standard | 25 mm | 5,5 mm | 118.8 mm | Super Alloy (nickel-based) | |
| F1858P*8 | FERREA | +1 mm | 26 mm | 5,5 mm | 118.8 mm | Super Alloy (nickel-based) |
Valve fitting
| Part | Honda original | Reinforced |
|---|---|---|
| Collets | 14781-PJ7-003 | KPR-5.5-7A-ST-16 |
| Valve stem seals | 12210-PJ7-003 / 12211-PJ7-003 | VS-H5.5E-8 / VS1002*8 (exhaust) |
| Valve guide | 12205-PJ7-305 | GDE-HD55-E-8 |
Check the groove of the chosen valve against the original 14781-PJ7-003 collets before reassembly.
At 25 mm, the seats keep their diameter; with the 26 mm F1858P, the 8 exhaust seats are machined to size.
On the D15B, Honda fits the 12210-PJ7-003 and 12211-PJ7-003 valve stem seals (1988), replaced in later years by PZ1 part numbers.
Technical guide
Our brands
| SUPERTECH, a Silicon Valley house, has devoted over 30 years to racing valvetrains: valves, springs, guides, titanium retainers. Each valve, be it stainless, titanium or Inconel, is born for a given engine and developed with rally, track and drag racing specialists. | |
| FERREA Racing Components was created in 1978 by Horacio Ferrea and his partner Daniel Urrutia. Stainless, titanium or nickel alloy valves leave its Florida and Argentina plants to equip engine builders in a great many countries, on NASCAR ovals as well as on drag strips. |
How to choose
The retainer squeezes the collets, which lock the valve in its groove, of which the SUPERTECH has only one. Two criteria remain to settle: head size, and brand, which determines the engines covered.
| Criterion | Option 1 | Option 2 |
|---|---|---|
| Size | Standard, 25 mm For exhaust seats at their original diameter, with no machining. SUPERTECH HEVN-1003 for the D15B and the D16A6, or FERREA F1857P for the D16A6 alone. New collets advised on reassembly. |
+1 mm, 26 mm The bigger head clears burnt gases faster and eases fresh charge in, which frees up power (around 10 to 12 cfm per mm of head). Taking the 8 seats to 26 mm also recovers seats already touched up. Only version: FERREA F1858P, D16A6 only. |
| Brand | SUPERTECH HEVN-1003 in black nitride stainless, at standard size, for the whole D15B family as for the D16A6. Its hardened surface limits stem wear; it is enough for an unboosted D15B or D16A6, on the road or on track days, with no other conversion. Single groove, KPR-5.5-7A-ST collets. |
FERREA F1857P and F1858P in Super Alloy, a nickel-based superalloy from the Competition Plus range, credited with 20 % more hot strength. Kept for the D16A6, at standard size or +1 mm; on a D15B, take the SUPERTECH. The one to keep for a D16A6 often run at full load. |
When reinforced valves become necessary
- Higher lift camshaft or reinforced valve springs fitted
- Higher, longer and more frequent revving
- Turbocharger grafted onto the D15B or D16A6
- Regular track, autotest or hill climb days
- Head to rebuild, with marked, burnt or tired exhaust valves
Vehicle compatibility
| Model | Engine code | Power | Years |
|---|---|---|---|
| Civic IV 1.6 i 16V (ED4) | D16A6 | 109 hp | 1987-1991 |
| CRX II 1.6 Si (ED9) | D16A6 | 110 hp | 1987-1991 |
| Civic IV 1.5 (EC, ED, EE, EF) | D15B1 | 71-82 hp | 1987-1993 |
| Civic IV 1.5 i 16V (ED3, ED6, EE2, SH4) | D15B2 / D15B4 | 90-98 hp | 1987-1993 |
| Civic V 1.5 i 16V (EG4, EG8) | D15B2 / D15B4 | 90-94 hp | 1991-1996 |
| CRX II 1.5 (ED, EE) | D15B6 | 63 hp | 1987-1991 |
| Civic V 1.5 (EG8, EJ2) | D15B7 | 91-101 hp | 1991-1996 |
| CRX III 1.5 (EG1) | D15B7 | 103-105 hp | 1993-1998 |
| Civic V 1.5 (EG) | D15B8 | 71 hp | 1991-1996 |
OEM part number (exhaust valve): 14721-PM3-000 (D15B)
Don't forget the inlet valves
A D15B or D16A6 cylinder head rebuilt as new deserves fresh inlet valves as well as new valve stem seals fitted in the same operation. The part designed for the D16A6:
| D16A6 inlet valves → |
-
Brand
-
ReferenceHEVN-1003-8