Skip to content
  • On order
Reinforced head gasket Porsche 944 968 M44 - C4274-027 Reinforced head gasket Porsche 944 968 M44 - C4274-027 Reinforced head gasket Porsche 944 968 M44 - C4274-027 Reinforced head gasket Porsche 944 968 M44 - C4274-027

Reinforced head gasket Porsche 944 968 2.7 3.0 M44.11 M44.12 M44.41 M44.43

€113.59 (tax incl.)
€151.45 (tax incl.) -25%

Reinforced Athena and Cometic head gasket, in Cut Ring and MLS for Porsche 944 and 968. Sold individually.

  • Brands: Athena, Cometic
  • Engines: M44.11, M44.12, M44.41, M44.43, M44.44
  • Bores: 105 to 106.5 mm
  • Thicknesses: 0.69 to 3.56 mm
  • Replaces: 944 104 394 04
C4274-027
0 in stock in France
ORDER TODAY, WE SHIP IN 3 WEEKS
Pay in installments

The Porsche engines covered

The 2.7 and 3.0-litre Porsche M44 is the inline four-cylinder petrol engine of the last-generation 944 and the 968. This page covers the M44.11, M44.12, M44.41, M44.43 and M44.44; the Cometic part numbers are listed for the first three.

The original gasket carries part number 944 104 394 04; for machined cylinder heads, Porsche specifies 944 104 394 51. Porsche publishes neither its construction nor its thickness; its bore is 106 mm. It is sized for standard combustion pressure: when that pressure rises, clamping load drops, the cylinder head lifts, and coolant passes into a cylinder.

Reinforced cylinder head gaskets

A cylinder head gasket does not create the seal on its own: it holds because the fasteners clamp the head against the block. A composite gasket is crushed for good beyond 100 N/mm² of admissible stress, whereas the 301 stainless steel of the MLS gaskets withstands 517 N/mm², 5 times more, and springs back at every combustion.

This page brings together the part numbers from two racing manufacturers, Athena and Cometic, in two constructions: Athena Cut Ring with stainless rings and Cometic MLS multi-layer steel. Gasket bores run from 105 to 106.5 mm, covering the standard block as well as the rebored block, and thicknesses from 0.69 to 3.56 mm, enough to adjust the compression ratio without touching the pistons or the cylinder head. As a rule, the gasket bore chosen is at least 0.5 mm larger than the actual cylinder bore. Each part number is sold individually, one gasket per engine.

Technical specifications

Gasket bore
OEM 106 mm
Thickness Gasket volume Gasket type
OEM not specified
Brand Part number
OEM 944 104 394 04
105 mm 1.14 mm 9.87 MLS Cometic H0472SP8045S
105 mm 1.60 mm 13.85 Cut Ring Athena 330043R
105 mm 2.49 mm 21.56 MLS Cometic H0472SP6098S
106 mm 0.69 mm 6.09 MLS Cometic C4274-027
106 mm 0.76 mm 6.71 MLS Cometic C4274-030
106 mm 0.91 mm 8.03 MLS Cometic C4274-036
106 mm 1.02 mm 9.00 MLS Cometic C4274-040
106 mm 1.14 mm 10.06 MLS Cometic C4274-045
106 mm 1.30 mm 11.47 MLS Cometic C4274-051
106 mm 1.42 mm 12.53 MLS Cometic C4274-056
106 mm 1.52 mm 13.41 MLS Cometic C4274-060
106 mm 1.68 mm 14.83 MLS Cometic C4274-066
106 mm 1.78 mm 15.71 MLS Cometic C4274-070
106 mm 1.91 mm 16.86 MLS Cometic C4274-075
106 mm 2.03 mm 17.91 MLS Cometic C4274-080
106 mm 2.13 mm 18.80 MLS Cometic C4274-084
106 mm 2.18 mm 19.24 MLS Cometic C4274-086
106 mm 2.34 mm 20.65 MLS Cometic C4274-092
106 mm 2.49 mm 21.97 MLS Cometic C4274-098
106 mm 3.05 mm 26.92 MLS Cometic C4274-120
106 mm 3.56 mm 31.42 MLS Cometic C4274-140
106.5 mm 1.30 mm 11.58 MLS Cometic H0472SP7051S

Gasket volume: the space the gasket leaves above each cylinder. It enlarges the combustion chamber, and the larger it is, the lower the compression ratio. Values compare with one another at identical gasket bore.

Preparation and fitting

Fasteners Engines Tightening torque
Original cylinder head bolts M44.11, M44.12, M44.41, M44.43, M44.44 Not published

Before fitting, check the flatness of the cylinder head and of the block with a straight edge and have them skimmed if necessary. None of these gaskets requires sealant: Athena and Cometic both supply them already coated.

Technical guide

The two constructions offered

Athena Cut Ring cylinder head gasket Athena Cut Ring
A gasket in reinforced, asbestos-free MO115 material (steel core, aramid fibres, NBR binder), supplied with separate AISI 304 stainless steel rings around each cylinder. Athena also intends it for turbocharged or nitrous engines above 2 bar, with no machining of the cylinder head or block. A silicone bead reinforces the sealing of the water and oil passages. On fitting, the ring embossments face the cylinder head. Athena rates the MO115 material at 100 N/mm² at most: the stainless rings are what hold combustion.
Cometic MLS cylinder head gasket Cometic MLS
Several stamped and riveted stainless steel layers. The outer layers carry active beads around each cylinder and each fluid passage. Sealing is achieved with a moderate clamping load and limited bore distortion. This is the versatile choice, from a prepared naturally aspirated engine to light forced induction.

Choosing bore and thickness

Gasket bore. The Athena Cut Ring comes in 105 mm, the Cometic MLS in 105, 106 and 106.5 mm.

Thickness. Porsche does not publish the thickness of the original gasket. A thicker gasket enlarges the combustion chamber and lowers the compression ratio; a thinner one reduces it and raises the ratio.

Your goal Thickness to choose
Keep the original compression ratio The value closest to the thickness of the removed gasket
Skimmed cylinder head, make up the lost height The thickness of the removed gasket + what was removed
Forced induction build, lower the ratio A thickness above that of the removed gasket
Naturally aspirated build, raise the ratio A thickness below that of the removed gasket

With a thickness finer than that of the removed gasket, measure piston protrusion above the block with a dial gauge: it is what determines the remaining clearance between piston and cylinder head.

The two brands

Athena Athena S.p.A. is an Italian manufacturer of engine gaskets and components, with its head office and main plant in Alonte, in the Veneto region. The group also produces in Spain, the United States, Brazil and India. Its multi-layer gaskets are fitted as original equipment by car manufacturers, and its racing range is designed and made entirely in Italy.
Cometic Cometic Gasket, Inc. is an American manufacturer of engine gaskets and sealing solutions, founded in 1989 and based in Concord, Ohio. Its speciality is the made-to-order gasket, in the bore and thickness required. All its products are made in the United States, from American materials.

Advantages over the original gasket

Criterion Original gasket 944 104 394 04 Reinforced gaskets
Construction Not specified by the manufacturer Multi-layer stainless steel
Gasket bore 106 mm 105 to 106.5 mm
Thicknesses available Not published by Porsche 0.69 to 3.56 mm, 22 values
Compression ratio adjustment None Through the thickness chosen
Resistance to overpressure Limited to standard output Designed for forced induction

When a reinforced gasket becomes necessary

  • Adding forced induction, or raising boost on an already turbocharged engine
  • Cylinder rebored beyond what the 106 mm bore of the original gasket covers
  • Looking for a compression ratio different from standard, higher or lower
  • Engine that has already lost its gasket, or is consuming coolant
  • Competition use, where the gasket goes through repeated temperature rises

Vehicle compatibility

Model Engine code Power Years
Porsche 944 M44.11, M44.12, M44.41 165 and 211 hp 1988-1991
Porsche 944 Cabriolet M44.41 211 hp 1988-1991
Porsche 968 M44.43, M44.44 239 hp 1991-1995
Porsche 968 Cabriolet M44.43, M44.44 239 hp 1991-1995

OEM part number: 944 104 394 04 ; 944 104 394 51 (culasses usinées).

Important: the 2.5-litre 944 (M44.01 to M44.10) take another original gasket (951.104.374.02): they are not covered by this page.

Why switch to a reinforced gasket?

A reinforced gasket holds where the standard one reaches its limit: at higher combustion pressure it keeps its shape instead of being crushed.

As soon as power goes up, turbo, supercharger or raised compression ratio, the head gasket becomes the weak link of the top end. Switching to a reinforced gasket is then not a comfort but a safeguard: it is what prevents the failure and the head removal that comes with it.

3 other products in the same category

Viewed products

Loading...