Skip to content
  • On order
Forged connecting rods Ford - 2.0L 16V Turbo - HMDA (Focus RS Mk1) for forged pistons Forged connecting rods Ford - 2.0L 16V Turbo - HMDA (Focus RS Mk1) for forged pistons

Forged connecting rods Ford - 2.0L 16V Turbo - HMDA (Focus RS Mk1) for forged pistons

€801.80 (tax incl.)
€1,002.25 (tax incl.) -20%

Set of 4 forged connecting rods in 4340 steel for the Ford Focus RS Mk1 2.0 16V Turbo (HMDA), 22 mm piston pin.

  • Brands: Wössner, I profile (A-Beam)
  • Compatibility: Focus RS Mk1 (DAW / DBW)
  • Engine codes: HMDA, 215 hp
  • Bolts included: ARP 2000 (3/8")
KCR085A
0 in stock in France
For larger quantities, 5 to 15 days lead time
Pay in installments

The Ford Focus RS Mk1 2.0 16V Turbo engine (HMDA)

The HMDA is the 2.0 L (1,988 cc) inline four-cylinder that brought the Focus into the RS family in 2002. With twin overhead cams and sixteen valves, force-fed by a Garrett turbocharger, it delivers 215 hp (158 kW) and pairs with a Quaife limited-slip differential to put its power down through the front axle. Built in limited numbers from late 2002 to late 2004, the first-generation Focus RS (DAW / DBW chassis) remains one of the most sought-after sporting front-drivers of its decade. As soon as boost and rpm are raised to chase more torque, the factory rod, designed for high-volume production, becomes the weak link of the rotating assembly. Replacing it with a set of weight-matched forged rods is the first safeguard of an HMDA that takes a build for the long term.

The forged connecting rods

Drop-forged and carefully machined, these rods withstand bending, compression and fatigue loads far beyond what the factory Focus RS rod tolerates. They suit every discipline: circuit, time attack, drift, drag, rally and hillclimb. Depending on the build level, they support a reliability-focused Stage 1 as well as a Stage 2 or a Stage 3 pushed on boost. Supplied as a complete set of 4, weight-matched, they preserve the balance of the four-cylinder rotating assembly. They adopt the HMDA's 22 mm piston pin, for a 137 mm center-to-center length.

Technical specifications of the Focus RS Mk1 forged rods (22 mm pin)

ReferenceBrandProfileBoltsPin Ø (mm)Small-end width (mm)Big-end Ø (mm)Big-end width (mm)Center-to-center (mm)Weight (g)
KCR085A Wössner I ARP 2000-3/8"-38mm 22 24,25 50 24,25 137 615

Tightening torque and stretch

Bearing clearance is checked with the cap tightened to its final figure: approximate tightening therefore makes every later measurement wrong, besides damaging the bearing itself. If the bolt stays below the range, the bore is not closed as intended, the clearance read is too large, and once running the missing preload lets the cap lift; the shell is hammered, crushed intermittently and the real clearance drifts further. If the bolt goes above the range, the bore is closed too far, the measured clearance looks correct while the big end is already oval and the shell pinched; the bolt itself has lost its elastic reserve and its preload falls as soon as the engine warms up. For the Wössner rod of this Focus RS and its 3/8" ARP 2000 fasteners, the torque and stretch figures in the table below are those of the fastener manufacturer and are not substitutes for one another. Stretch measurement with a dial gauge remains the reference method; ARP assembly lubricant and kit instructions take priority.

RodBoltsTightening torqueRecommended stretch (mm)
Wössner I (KCR085A) ARP 2000 74,6 N·m 0,140 – 0,152

Forged rods technical guide

4340 forged steel

These rods are forged from 4340, a low-alloy nickel-chromium-molybdenum steel that serves as the benchmark for the high-performance rod. Die-forging, followed by quenching and tempering, keeps a continuous grain flow behind its high tensile strength and outstanding fatigue endurance, two decisive qualities on a boosted, heavily stressed HMDA. Against a factory fracture-split rod optimised above all for manufacturing cost, a forged 4340 rod gains roughly +19% yield strength, +8% tensile strength and +19 to +37% fatigue endurance. It is this mechanical reserve that absorbs the torque and boost increases of a prepared engine without breaking.

The rod profile

The range is offered in the I profile, by Wössner. The I-beam offers an excellent balance between stiffness and mass, particularly relevant on a 2.0 L turbo where a light rotating assembly matters as much as bending resistance. Wössner offers it in its A-Beam form, an optimised I-beam, to combine lightness and strength. The specification table gives the center-to-center length, big-end diameter, big-end width and weight of the reference.

I profile: I profile: two flanges frame a thinner central web and give the body its “I” shape, which Wössner machines in its A-Beam version: the rod stays very stiff without adding mass to the rotating assembly. On modern turbocharged engines such as the Focus RS HMDA, this profile is favoured both to make the bottom end reliable and to follow a rise in boost pressure.

How to choose your rod bolts? ARP

ARP ARP 2000: the all-round benchmark alloy, with a tensile strength of about 220,000 psi (1,517 MPa). Offered here in 3/8" diameter, it handles the most demanding HMDA builds, up to about 200 hp per cylinder, at speeds reaching 8,500 rpm. Sturdy, reliable and with no storage constraints, it is the reference bolt to make a prepared Focus RS reliable, from Stage 1 to Stage 3.

Measuring bolt stretch

Measuring bolt stretch

On a forged rod, the correct bolt preload is checked by its stretch, measured with a dial gauge, rather than by torque alone: lubrication and run-in distort the torque reading. Always refer to the stretch values from the bolt manufacturer, shown in the table above.

Discover the ARP stretch gauge

The brand offered

Wössner Wössner is a German forging specialist for engine building, whose pistons and connecting rods are found in karting, motorcycle and competition car engines alike. The KCR085A rod is hot-forged then machined from 4340 steel in the in-house A-Beam profile, an optimised I-beam, with ground and gauged small and big ends. Every set of four is weight-matched to preserve the balance of the HMDA and ships with its dedicated ARP 2000 3/8" 38 mm bolts.

Glossary

1) Small end
2) Small-end diameter
3) Rod beam
4) Rod bolt
5) Big end
6) Rod nut / bolt
7) Rod cap
8) Big-end diameter
9) Center-to-center

Vehicle compatibility

These forged rods fit the first-generation Ford Focus RS powered by the 2.0 L 16-valve turbo (HMDA code):

BrandModel (chassis)Engine codePowerYears
Ford Focus I RS (DAW / DBW) HMDA 158 kW (215 ch) 2002–2004

Why is it the most economical solution?

On a tuned HMDA the stock rod is the first component to let go, and a failure under high boost never stays confined to the guilty part: it scores the crankshaft, damages the bores and usually writes off the whole block.

Rebuilding with factory parts after a failure means buying rods, pistons and often a crankshaft again, only to end up with exactly the limits that caused the breakage. For a comparable invoice, a set of forged 4340 rods combined with forged pistons brings an incomparable safety margin and keeps the door open to a later power increase.

For the same budget: a more reliable, longer-lived HMDA, ready for the next stage of tuning.

6 other products in the same category

Viewed products

Loading...